Stimmen - 3, Durchschnittliche Bewertung: 4.3 ( )

Hersteller: Nilfisk-ALTO Dateigröße: 5.4 mb Dateiname: Unterrichtssprache:

Brushes For cars and other surfaces. Available in more shapes. Tube cleaner 15 m long tube cleaner for the cleaning of tubes and drains. Water-sand- For removal of paint and rust. blasting equipment Sand available from do-ityourself shops. Patio Cleaner Equipment for quick cleaning of patio/ drive/fl agstones. Foam sprayer (3) Equipment for the application of foam. Distance approx. 1 m. Garden brush Rotating brush for cleaning of wooden surfaces. Rim brush Rotating brush for cleaning of wheel rims. Wall accessosries Rack for storage storage of hose, spray handle, nozzles etc. Hose guidance Hose guidance for stationary use of high pressure washer. Can be mounted on the wall - even around corners. Wall hook For suspension of your high pressure washer on the wall. Water hose reel To update trolley models with a hose reel solution. Includes 25 m garden hose. Detergents Stone & Wood For fl agstones, brick- and Cleaner woodwork. Suitable for moss and algae. Plastic Cleaner For plastic and synthetic materials such as garden furniture. Accessories EN Metal Cleaner For cleaning of metal such as garden tools. Car Combi Cleaner For cars etc. With rinsing wax. Alu Cleaner For surfaces of aluminium. Applied with an atomizer. Oil & Grease Cleaner For cleaning of grease and oil on motors for instance. Applied with an atomizer. Wood Cleaner For cleaning of wooden surfaces incl. of wooden garden furniture. 4.0 Maintenance EN WARNING! Always disconnect the electrical plug from the socket prior to maintenance or cleaning. To ensure a long and problem free working life, please take the following advice: • Wash out water hose, high pressure hose, spray lance and accessories before mounting. • Clean the connectors of dust and sand. • Rinse the detergent spraying attachment after use. Any repair should always be made in an authorized workshop with original spare parts. 4.1 Cleaning of nozzle A clogging up in the nozzle causes a pump pressure which is too high. This is why cleaning is required immediately. 1. Stop the machine and disconnect the nozzle. 2. Clean the nozzle. IMPORTANT: The cleaning tool (4) should only be used when the nozzle is detached! 3. Flush the nozzle backwards with water. 4.2 Cleaning of water inlet fi lter Clean the water inlet filter regularly once a month or more frequently according to use. Carefully loosen the filter with a screwdriver and clean it. Check that it is intact before re-mounting it. Maintenance EN The inlet filter must always be fitted inside the water inlet pipe to filter out sand, limestone and other impurities, as they will damage the pump valves. CAUTION: Failure to fit the filter will invalidate the guarantee. 4.3 Cleaning of machine vents The machine should be kept clean so as to let cooling air pass freely through the machine vents. 5.0 Storage EN The machine should be stored in a frost-free room! Pump, hose and accessories should always be emptied of water prior to storing as follows: 1. Stop the machine (press the On/Off switch “O” (1) and detach water hose and accessory. 2. Restart the machine and activate the trigger (9b). Let the machine run until no more water runs through the spray gun (9). 3. Stop the machine, unplug and wind up hose and cable (5). 4. Place spray handle, nozzles and other accessories in the holders of the machine. Should the machine by mistake be frozen, it will be necessary to check it for damage. NEVER START-UP A FROZEN MACHINE. Frost damages are not covered by the guarantee! 6.0 Environmental protection Recycle unwanted materials instead of disposing of them as waste. All tools, hoses and packaging should be sorted, taken to the local recycling center and disposed of in an environmentally safe way. 7.0 Trouble shooting guide EN To avoid unnecessary disappointments, you should check the following before contacting the ALTO service organization: Symptom Cause Recommended action Machine refuses to start Machine not plugged in Defective socket Fuse has blown Defective extension cable Plug in machine. Try another socket. Replace fuse. Switch off other machines. Try without the extension cable. Fluctuating pressure Pump sucking air Valves dirty, worn out or stuck Check that hoses and connections are air- tight. Clean and replace or refer to local ALTO distributor Pump seals worn out Clean and replace or refer to local ALTO distributor. Motor busses Low voltage or low temperature Activate the trigger of the spray gun. Machine stops Fuse has blown Incorrect mains voltage Thermal sensor activated Replace fuse. Switch off other machines. Check that the mains voltage corresponds to specification on the model tag. Leave the washer for 5 minutes to cool down. Nozzle partially blocked Clean the nozzle (see section 4.1) Fuse blows Fuse too small Change to an installation higher than the amp. consumption of the machine. You may try without the extension cable. Machine pulsating Air in inlet hose/pump Inadequate supply of mains water Nozzle partially blocked Water filter b...

Herunterladen

Geben Sie zwei Ziffern: