Stimmen - 1, Durchschnittliche Bewertung: 3 ( )

Hersteller: Nilfisk-Advance America Dateigröße: 3.6 mb Dateiname: Unterrichtssprache:

from your own well), an additional fi lter should be mounted. 1. Let the water run through the water hose before connecting it to the machine to prevent sand and dirt from penetrating the machine. Note: Check that the fi lter is fi tted in the water inlet pipe and that it is not clogged up. 2. Connect the water hose to the water supply by means of the quick connector (inlet water, max. pressure: 10 bar, max. temperature: 50°C). 3. Turn on the water. 8 4.5 Start and stop of the machine (when connected to a water supply) The spray lance is affected by a thrust during operation - therefore always hold it fi rmly with both hands. IMPORTANT: Point the nozzle at the ground. 1. Check that the machine is in upright position. NOTE: Do not place the machine in high grass! 2. Release the trigger lock. 3. Activate the trigger of the spray gun and let the water run until all air has escaped from the water hose. 4. Turn the start/stop switch (1) to position "I". 5. Activate the trigger of the spray gun. Always adjust the distance and thus the pressure of the nozzle to the surface, which is to be cleaned. Do not cover the machine during operation. Note: If the machine is left or not used for 5 minutes, it must be switched off on the start/stop switch "O" (1): 1. Turn the start/stop switch to position "O". 2. Disconnect the electrical plug from the socket. 3. Shut off the water supply and activate the trigger to relieve the machine of pressure. 4. Lock the spray gun. When releasing the trigger of the spray gun, the machine automatically stops. The machine will start again when you re-activate the spray gun. 4.4 Telescopic handle The machine features a telescopic handle. To raise or lower the handle, press the knob and move the handle upwards or downwards. When a click is heard, the handle is in right position. Use an external fi lter if the water contains impurities. 2. Turn the start/stop switch to position "I". 3. Activate the trigger of the spray gun and let the water run, until the air has escaped from the water hose and the pump. 4. Mount spray lance and nozzle. The washer can take in water from a rain water tank as an example. The hose for the water supply must not be too long, approx. 5 m. Make sure that the water tank is not placed on a lower level than the machine. 1. Place the other end of the water hose in the water tank. 4.6 Start the machine (when connected to open containers (suction mode)) 9 4.7 Pressure regulation on the TORNADO® PRnozzle The pressure can be regulated on the TORNADO® PR nozzle. 4.8 Stationary use If mounting a special wall hook (not standard), the pressure washer can be used as a stationary solution meaning that it can be operated while hanging on the wall. Only mount the wall hook on a sturdy wall. Adjust the length of the screws and size of rawlplugs to the type of wall. On the wall hook garden/rim brush (a) foam sprayer (b), Click & Clean brush (c) and Click & Clean nozzles (d) can be stored. Important: The bearing capacity of the wall hook is max. 30 kg. .. .. .. .. .. .............. .............. High pressure Low pressure 5 Fields of application and working methods 5.1 General Efficient high presure cleaning is achieved by following a few guidelines, combined with your own personal experience of specific cleaning tasks. Accessories and detergents, when correctly chosen, can increase the efficiency of your pressure washer. Here is some basic information about cleaning. 5.1.1 Detergent and foam Foam or detergent should be applied onto dry surfaces so that the chemical product is in direct contact with the dirt. Detergents are applied from bottom to top, for example on a car bodywork, in order to avoid "super clean" areas, where the detergent collects in higher concentration and streams downwards. Let the detergent work for several minutes before rinsing but never let it dry on the surface being cleaned. Note: It is important that the detergents do not dry up. Otherwise the surfac that has to be cleaned can be da maged. 5.1.2 Mechanical effect In order to break down tough layers of dirt, additional mechanical effect may be required. Special wash brushes offer this supplementary effect that cuts through dirt (especially by car washing). 10 5.2 Typical fields of application Below you will find a description of a lot of cleaning tasks which can be solved by a pressure washer from Nilfisk in association with accessories and detergents. Task Accessories ‘Click & Clean’ Cleaning method Car Car nozzle, auto brush, underchassis nozzle, Foam sprayer, Car Combi Cleaner 1. Apply Car Combi Cleaner with the foam sprayer. Always start from the bottom and work upwards. Let Car Combi Cleaner act for at least 5 min. 2. Wash the car with the car nozzle, which has been optimized for quick and gentle cleaning of enamelled surfaces (the jet is wider and not so sharp). Start at the front of the car and work back- wards to avoid water from penetrating by the door mouldings. 3. Use the brush for removal of tra...

Herunterladen

Geben Sie zwei Ziffern: