Stimmen - 2, Durchschnittliche Bewertung: 4.5
(
)
)
|
Anleitung Zusammenfassung
1. Place nozzle extension through hole on accessory tray, as shown in Figure 13. 2. Place spray gun through hole on accessory tray on right side of unit (Figure 13). NOTE: You may also use the hooks attached to the base and handle to store your gun and nozzle extension, as shown on page 6. 3. Insert multi–colored quick connect spray tips in holes on accessory tray as shown in Figure 13. 4. Hang high pressure hose on hook attached to accessory tray on front of tray, as shown in Figure 13. How to Use Quick Connect Spray Tips The quick–connect on the nozzle extension allows you to switch between four different quick connect spray tips.The spray tips vary the spray pattern as shown (Figure 14). Follow these instructions to change spray tips: 1. Engage trigger lock on spray gun. Figure 13 — Typical Accessory Tray • NEVER exchange spray tips without locking the trigger lock on the spray gun. • DO NOT twist spray tips while spraying. A pressure washer produces a high pressure spray which increases risk of injury and damage to unit. CAUTION 40° White 1650 PSI 2.2 GPM 15° Yellow 1950 PSI 2.1 GPM 0° Red 2200 PSI 1.9 GPM Black Use to apply detergent Figure 14 — Spray Tip Spray Patterns Low Pressure High Pressure Section 4: Operation 2. Pull back collar on quick–connect and pull current spray tip off. Store spray tips in holder provided on the accessory tray. 3. Select desired spray tip: • For delicate rinse (lower pressure and higher flow), for gentle cleaning of cars/trucks, boats, RV’s, patio furniture, lawn equipment, etc., select white 40° spray tip. • For general rinsing (medium pressure and medium flow), ideal for most all purpose cleaning such as home siding, brick patios, wood decks, driveways and sidewalks, garage floors, etc., select yellow 15° spray tip. • For maximum rinsing (higher pressure and lower flow), for stubborn or hard to reach surface such as second story surfaces, paint removal, oil stains, rust removal or other stubborn substances (tar, gum, grease, wax, etc.), select red 0° spray tip. • To apply chemical, applies project specific cleaners to help break down stubborn dirt and grime on a variety of surfaces, select black detergent spray tip. 4. Pull back on collar, insert new spray tip and release collar.Tug on spray tip to make sure it is securely in place. 5. For most effective cleaning, keep spray tip from 8 to 24 inches away from cleaning surface. If you get spray tip too close, you may damage cleaning surface. 6. DO NOT get closer than 6 inches when cleaning tires. Cleaning and Applying Detergent IMPORTANT: Use detergents designed specifically for pressure washers. Household detergents could damage the pump. CAUTION You must attach all hoses before you start the engine. • Starting the engine without all the hoses connected and without the water turned ON will damage the pump. • Damage to equipment resulting from failure to follow this instruction will void warranty. To apply detergent follow these steps: 1. Review spray tip use. 2. Prepare detergent solution as required by manufacturer. 3. Place small filter end of detergent siphoning tube into detergent container. CAUTION Keep the detergent siphoning tube from coming in contact with the hot muffler. • When inserting the filter into a detergent solution bottle, route the tube so as to keep it from inadvertently contacting the hot muffler. 4. Make sure black detergent spray tip is installed. NOTE: Detergent cannot be applied with the high pressure spray tips (White,Yellow or Red). 5. Make sure garden hose is connected to water inlet. Check that high pressure hose is connected to spray gun and pump and start engine. 6. Apply detergent to a dry surface, starting at lower portion of area to be washed and work upward, using long, even, overlapping strokes. 7. Allow detergent to soak in between 3–5 minutes before washing and rinsing. Reapply as needed to prevent surface from drying. DO NOT allow detergent to dry on (prevents streaking). IMPORTANT:You must flush the detergent siphoning system after each use by placing the filter into a bucket of clean water, then run the pressure washer in low pressure for 1-2 minutes. 13 Section 4: Operation Pressure Washer Rinsing For Rinsing: 1. Engage trigger lock on spray gun. 2. Remove black detergent spray tip from nozzle extension. 3. Select and install desired high pressure spray tip following instructions “How to Use Quick Connect Spray Tips”. 4. Keep spray gun a safe distance from the area you plan to spray. WARNING High pressure spray could cause you to fall if you are too close to the cleaning surface. • Keep spray nozzle between 8 to 24 inches away from cleaning surface. • Operate this unit on a stable surface. • Be extremely careful if you must use the pressure washer from a ladder, scaffolding or any other relatively unstable location. • Firmly grasp spray gun with both hands when using high pressure spray to avoid injury when gun kicks back. 5. Apply a high pressure spray to a small area and then...