Anleitung Graco Inc., modell Hydra-Clean 1204E
Hersteller: Graco Inc. Dateigröße: 563.3 kb Dateiname: 1989bbe8-d347-4892-bca5-c51698665819.pdf
Unterrichtssprache:
|
|
|
|
Link zum kostenlosen Download Hinweise finden Sie am Ende der Seite
Anleitung Zusammenfassung
OBSERVE ALL WARNINGS. Read and understand all instruction manuals before operating equipment. ~. ~.. . ,.. ,. .",. ;~..._il_x_~**"~. INJECTlON :.. .~, .. . , . ,,,: ... i.-:*.'. .,-.'i .,.._,,,*+ ,>,i ~~.<,.,, ,*.,.,,.._c. FIRE fluids under high pressure from spray or leaks can Do not spray flammable liquids. Do not operate the unit penetrate the skin and cause extremely serious injury, where combustible fumes or dust may be present. including the need for amputation. . . . -,. ., .. ,,..,I ,.., ..1. . . > .. , ~~ GENERAL . ,, .:, :k;k' ,,.!$.,,>~. :. .: NNER point the spray gun at anyone or any part of the ' ' body. NNER run the unit with the belt guard removed. Keep clear of moving parts whenthe unit is running. NNER put hand or fingers over the spray tip. Observe detergent manufacturer's safety precautions. NNER try to stop or deflect leaks with your hand or Avoid getting detergent or other liquids in your eyes. body. Follow the directions contact on the container regarding with eyes, nose, and skin, breathing fumes, etc. Always ALWAYS have the tip guard in place when spraying. wear full goggles to protect your eyes from the spray as well as any debris dislodged by the spray. If necessary, MEDICAL TREATMENT&~;T:",'? ''.X wear gloves or other protective clothing. If antidotes or treatment are recommended, be prepared to use them. If any fluid appears to penetrate your skin, get EMERGENCY MEDICAL CARE AT ONCE. DON'T spray toxic chemicals such as insecticide or weed killer. BO NOT TREAT AS A S!MPLE CUT. Tell the doctorexactlvwhatfluld was miected. For treatment instructions have your doctor Cali the This unit has a 3-prong grounding plug to protect you NATIONAL POISON CENTER NETWORK from electric shock. Be sure to plug the unit intoa pro- (412)681-6669 perly grounded outlet that will accept the 3-prong plug. Do not remove the thirdprong. AVOID COMPONENT RUPTURE"~~,-:r_',":;i.'. The green wire of the electric cord is connected to the Even after you shutoff the electric motor, there is high unit chassis and motor frame and the other twowires pressure in the pump, hose and gun untilyou relieve it are connected to themotorswitchfor grounding by triggering thegun. So before removing the spray tip continuity. or servicing the unit, ahys shut off the unit andtrigger the gun to release pressure. The electric motor has an overload protection device which automatically shuts off the motor ifit overheats. Be sure that all accessory items and system com-So, before examining or working on a motor which has ponents will withstand the pressure developed. NNER stopped, shut off the unit, relieve pressure and pull out .exceed the pressure rating of any component in system. the electrical plug. This will avoid the hazard of the NNER alter or modifyequipment-your personal motor starting unexpectedly. safety, as well as the function of the equipment, is at stake. ALWAYS CHECK to be sure the switch is OFF and that the hoses and electric cord are clear of moving parts Before each use, check hose for weak, worn or damag-before plugging in the power cord. ed conditions caused by traffic, sharp corners, pinching or kinking. Tightenall fluid connections securely before each use. Replace any damaged hose. Do not use chemicals or agents which are not compati- ble with Buna-N and PVC or neoprene cover of hose. Do not leave a pressurized unit unattended. Shutoff the unit and relieve pressure before leaving. IMPORTANT ." United States Government safety standards have been adopted under the Occupational Safety and Health Act. These standards -particularly the General Standards, Part 1910, and the Construction Standards, Part 1926 -should be consulted in connection with your use of airless spray equipment. 2, 801-238 INs1 Check Electrical Service and Plug In Before plugging in the sprayer,besure the electrical service is 220 V, 60 HzAC, 20 Amp. With the ON-OFF switch in the OFF position, plug the power supply cord into a grounded outlet. Do not remove the thirdprong of theplug1 If youuse an extension cord, it mist have 3 wires of at least 12 gauge (2.5 mm2) and should not be over 100 ft (30.3 m) long. Install Wheels and Handle Slide the axle through theframe. Slide the wheels onto the axle and secure kith the cotter pins provided. Install the hub caps. Using the two lowest holes on each leg of the frame, at- tachthe handle with the 4 screws, flat washers, lockwashers and nuts provided. Install Hose and Spray Gun Connect the quick coupler on the end of the tube tothe tip assembly. Connect the hose assembly to the quick coupler at the fluid inlet of the gun. Then connect the hose to the Hydra-Clean unit. Removethe tape from the cap on the top of the pump. Clean Accessories For spraying detergent or other cleaning solution, we OPERATION Startup Before starting, be sure to read the safety warningsand setup water theTurn on supply. .. recommend using a chemical injector kit. See Ac- cessories and instruction manual 801-192 for installation an...