Stimmen - 1, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
ECHO provides this Operator's Manual which must be read and understood for proper and safe operation. 99922202237 03/92 STANDARD EQUIPMENT © Oil plug (2) Pressure adjusting knob (3) ON/OFF switch (4) High pressure hose connection (OUTLET) (5) Inlet hose connection with water filter (INLET) (6) Chemical filter (7) Chemical regulator (CHEM) 2 Pressure indicator Oil level indicator Automatic gun High pressure hose “QUICK-LANCE” “ROTOX” (or “MULTIREG”) IMPORTANT SAFETY INSTRUCTIONS This book has important information for the use and safe operation of this machine. Read and understand all warnings before you start working. W A R N I N G - WHEN USING THIS MACHINE: 1. Read all the instructions before using the machine. 2. To reduce risk of injury, close supervision is necessary when the machine is used near children. 3. Know how to stop the machine and bleed pressure quickly. Be quite familiar with the controls. 4. Stay alert! Watch what you are doing. 5. Do not operate the machine when fatigued or under the influence of alcohol or drugs. 6. Keep operating area clear of all persons. 7. Do not overreach or stand unstable support. Keep good footing and balance at all times. 8. Follow the maintenance instructions specified in the manual. 9. Read carefully instructions concerning grounding and extension cords on page 41. 10. To prevent fire hazard, do not use with or near inflammable such as: gasoline, grain dust, solvents and thinners. Only use a cleaning concentrate recommended by the chemical manufacturer. W A R N I N G - RISK OF INJECTION OR INJURY. DO NOT DIRECT DISCHARGE STREAM AT PERSONS. SAVE THESE INSTRUCTIONS 3 IMPORTANT = PRECAUTIONS WARNINGS The unit must not be run without water. Lack of water will cause serious damage to the seals. Do not pull cable in order to unplug. Do not pull hose in order to move the unit. Do not damage or effect risky repairs on electric cable. Have worn, cut or damaged cords and plugs replaced by an authorized service person. To prevent injury, always disconnect plug before disassembling any part of the unit or effecting any servicing and before leaving the machine. 5EBF Avoid storing the unit in cold places where there is danger of freezing. Keep the unit in a dry building. 4 When the unit is working, do not cover and do not place in a closed space where ventilation is insufficient. Do not work in the rain, or during thunderstorms. To reduce the risk of electric shock: a) do not direct the jet of water on to the unit or any other electrical part; b) always wear rubber soled footwear when operating the unit. When using an extension cable, it is essential to follow the instructions given in the "INSTALLATION" section (Page 5). Wrong choice of cable dimension can damage or jeopardize the functioning of the unit. It is important not to run unit for more than 5 minutes with the gun in closed position. Should it run for a longer period, the temperature of the re-circulating water will increase rapidly and could risk damaging the pump seals. INSTALLATION Check that the oil in the sight glass is at the half-way level. 6 7 —....................= CHECKING AND CHANCING THE OIL ==5 — The level of the oil must be checked periodically. — The first important oil change must be carried out after the first 20 hours of work and successively everv 150 hours. — In any case we suggest an oil change at least once a year. — Oil type: SAE 20/30. — Capacity: 0,33 litres. CHECKING THE WATER FILTER ===== It is important to check and clean periodically the water filter in order to avoid restricting the water flow due to deposits in the filter screen. Remember that a well-cleaned filter means good performance and long life to the unit. = PRECAUTIONS AGAINST FREEZINC If the unit is to be stored in a place where there is risk of freezing, we suggest feeding some antifreeze into the pump, similar to that used in your car. In any case, at very low temperatures if in doubt that some parts of the unit may be frozen or if the unit has been in store for a long time, before plugging in, we suggest, to turn the motor shaft with the key supplied. This operation permits to find out if the unit is frozen or blocked due to lime scale deposits. Taking these precautions before starting, you will avoid damaging the unit. Remove the key before switching on motor. 8 TROUBLE SHOOTING FAULT CAUSE REMEDY Pump running normally but pressure does not achieve rated values Pump sucking air Valves worn or dirty Unloader valve seat faulty or worn Nozzle incorrect or worn Worn piston packing Check that hoses and fittings are air tight. Check, clean or replace. Check and replace. Check and replace. Check and replace. Fluctuating pressure Valves worn dirty or stuck Pump sucking air Worn piston packing Check, clean or replace. Check that hoses and fittings are air tight. Check and replace. Pressure drops after period of normal use Nozzle worn Valves worn, dirty or ...