Stimmen - 3, Durchschnittliche Bewertung: 3.7
(
)
)
|
Anleitung Zusammenfassung
Irregular pressure Gun or Hose failure Replace Gun and/or Hose. Contact us at: customerservice@huskypowerwasher.com or order online at: Kink in the Garden Hose or Hose is wrapped on a storage wheel Unwrap the Garden Hose and lay it out flat to ensure that there are no kinks in the Hose. Water leaking from either Hose or Unit Stop water from leaking before using the unit or contact us if you need assistance. Garden Hose length is too long Shorten the length of the Garden Hose. We recommend a maximum length of 25 to 50 feet for City water supply and 30 feet for Well water supply. Clogged Nozzle Clean the Nozzle as instructed in section 6.2. Air in Pump Let Pressure washer run with Gun trigger depressed and Wand removed until a steady stream of water is released. No Wand attached to the front of the Gun Attach Click-N-CleanTM Wand to the front of the Gun. (High Pressure is created with the Wand and not the Gun). No water coming out of Wand Clogged Nozzle Clean Nozzle as instructed in section 6.2. Sceen Filter is clogged Clean the Sceen filter as instructed in section 6.4. Kink in the Garden Hose or Hose is wrapped on a storage wheel Unwrap the Garden Hose and lay it out flat to ensure that there are no kinks in the Hose. 20 HUSKY 1550 PROBLEM OR CONCERN POSSIBLE CAUSE SOLUTION No water coming out of Wand Gun/Hose Assembly is defective Attach the Gun/Hose to the front of the unit with no wand attached to the Gun. Squeeze the trigger of the gun to ensure that water comes out of the front of the Gun at a rate equal to the Garden Hose. If no water comes out of the Gun, remove the gun and the hose to ensure that water flows out of the pump. If it does, the gun will need to be replaced. Contact us at: customerservice@huskypowerwasher.com or order a replacement directly online at: Trigger will not move Gun Safety Lock in engaged Release Safety Lock as instructed in Manual. Unit will not start Unit is not turned on Press ON/OFF Switch into ON position. Note: Unit will only start when trigger is depressed. Unit stops while operating Loose or disconnected Plug Reconnect Plug. Defective GFCI Plug Perform GFCI reset procedure as instructed in Section 4.3. If the GFCI does not reset it will need to be replaced. Contact us at: customerservice@huskypowerwasher.com or order a replacement directly online at: Extension Cord length or gauge incorrect Use proper Extension Cord as instructed in section 4.3. Gun trigger not operating properly Contact us at: customerservice@huskypowerwasher.com or order a replacement directly online at: Defective Gun Remove the Gun and Hose assembly from the front of the unit. Aim water stream away from electric source and switch the unit into the ON position. If the unit starts and water comes out of the front, the Gun may need to be replaced. Contact us at: customerservice@huskypowerwasher.com or order a replacement directly online at: Tripped Pressure washer Thermal Switch Allow to cool and restart unit. Defective ON/OFF Switch Contact us at: customerservice@huskypowerwasher.com or order a replacement directly online at: Unit will not stop when trigger is released Screen filter is clogged Clean the Screen filter as instructed in the section 6.4. Garden Hose is kinked or leaking water Make sure the Garden Hose is laid out flat and there are no kinks in it. The hose should not be wrapped on a storage wheel. Make sure the faucet is open all the way and there is a full volume of water reaching the unit. 21 HUSKY 1550 PROBLEM OR CONCERN POSSIBLE CAUSE SOLUTION Wand is malfunctioning Test wand to ensure that it is not malfunctioning. Gun is not operating properly Remove Wand from the Gun and squeeze trigger to ensure that the water is coming out of the front of the Gun at a rate equal to the Garden Hose. Wand - Attaching To attach the Wand apply some moderate downward pressure on the Wand (In the direction of the trigger) while simultaneously twisting the wand a 1/4 of a turn counterclockwise. (It may help if you set the gun vertically on a flat surface with the wand pointing upwards). The two tabs on the end of the Wand must slide all the way in before the Wand will twist and lock. If this does not work remove the o-ring from the end of the wand and attach it without the o-ring. If the wand attaches, you will need to replace the o-ring. Contact us at: customerservice@huskypowerwasher.com or order a replacement directly online at: Wand - Removing Release the back pressure in the Gun/Hose. Remove the Garden Hose from the unit and squeeze the trigger of the Gun. Apply some moderate downward pressure on the Wand (In the direction of the trigger) while simultaneously twisting the wand a 1/4 of a turn clockwise. (It may help if you set the gun vertically on a flat surface with the Wand pointing upwards). For additional assistance...
Dieses Handbuch ist für folgende Modelle:Hochdruckreiniger - 1550 PSL (3.65 mb)