Stimmen - 5, Durchschnittliche Bewertung: 4.4
(
)
)
|
Anleitung Zusammenfassung
III.) Before Starting WARNING: Make sure all switches and controls are in the OFF position prior to plugging in the cord. DO NOT stand in water while plugging or unplugging electrical cord. WARNING: Use a UL recognized receptacle protected by a ground fault interrupter and extension cord of proper voltage and amperage at all times. 1. Connect electrical cord to specified NEMA receptacle. See page 4. WARNING: Check hoses, fittings, wand, trigger gun and fuel connections daily for signs of wear, cracks and looseness, and replace as required. 2. Connect water supply hose to the garden hose connector located on the pump. 3. Fill the burner fuel tank. We recommend kerosene because it burns cleanest. #1 grade home heating oil, #1 or #2 diesel can also be used. DO NOT USE GASOLINE OR CRANKCASE OIL. 4. If detergents will be used, only use detergents intended for pressure washers. Follow instructions on the detergent container. IV.) To Start DANGER: Do not point the spray wand at yourself or at any person. Bodily injury may result from water under high pressure. WARNING: Wear eye, ear, hand, foot and skin protection at all times while operating this pressure washer. IMPORTANT: The water must be turned on before starting. Running the pump dry will cause damage and void warranty. 1. Turn water supply ON. 2. Squeeze the trigger to allow air to purge from the system. (this step goes faster with the pressure nozzle removed) V.) Attach Nozzle Nozzle Color of Nozzle: Spray Angle Used For: Red 0 Highest Impact Yellow 15 Tough Stains/ Stripping Green 25 General White 40 Light Cleaning Yellow 15 Steaming Your pressure washer is equipped with five nozzles. To install a nozzle simply pull back the collar and push the nozzle into the coupler. Once the connection is made, pull on the nozzle to assure a tight connection. Nozzle Collar Coupler Lance CORRECT INCORRECT WARNING: Make sure the nozzle is correctly inserted. The nozzle may become a projectile if not inserted correctly. Do not attempt to use different types of nozzles that may not fit the coupler. VI.) Turn the pump switch ON. 1. Make sure the hose is not kinked. A kinked hose will provide insufficient water supply to the pump and will reduce its life. Make sure the hose remains unkinked after moving the pressure washer. VII.) For Hot Water 1. If HOT water is desired, make sure there is fuel in the fuel tank, turn the heat switch ON, and adjust the thermostat to the desired temperature(if applicable). The burner will fire when the trigger is squeezed. You may need to initially adjust your burner for peak performance. See the “Oil Burner” section under INSTALLATION. When the trigger is released or the temp setting is reached, the burner will automatically turn off. IMPORTANT: Do not run the machine in hot mode without any fuel in the fuel tank. The fuel pump will be damaged if it is run dry. To Clean WARNING: Wear eye, ear, hand, foot and skin protection at all times while operating this pressure washer. DANGER: Do not point the spray wand at yourself or at any person. Bodily injury may result from water under high pressure. CAUTION: Be careful on painted or delicate surfaces, the pressure may damage the surface if the nozzle is too close. IMPORTANT: Your spray gun is equipped with a built-in trigger safety latch to guard against accidental trigger actuation and potentially dangerous high-pressure spray. Rotate the safety latch to the locked position when not spraying. NOTE: Your pressure washer is equipped with a low pressure chemical injector. You do not need to use chemicals for every job, however, the proper chemical used for the proper application can speed up cleaning jobs tremendously. WARNING: Only use North Star pressure washer chemicals or chemicals specifically formulated for pressure washers. Follow the chemical manufacturer’s recommendations. Understand all safety precautions and first aid for all chemicals. 1. Snap the quick couple chemical injector onto the high pressure water outlet and high pressure hose and submerge the suction strainer into the chemical solution. Adjustment Knob Strainer High Pressure Hose Water Outlet Diluted Chemical Chemical Injector 00322 2. The amount of chemical applied can be changed by turning the chemical adjustment knob located on the chemical injector. 12 3. Rotate the grip on the dual lance wand to change to low pressure and start the detergent flow. 4. Spray detergent onto the surface and allow it to soak. Chemicals need time (dwell time) to work properly. Follow the chemical manufacturer’s recommendations for dwell time. 5. Change back to high pressure by rotating the grip until water comes out the right lance only. 6. Hold the lance with two hands, have a sturdy stance. 7. Point lance at dirty surface and squeeze trigger. 8. Wash from the bottom to the top, using side to side motions. This washes away heavy dirt and allows the detergent to soak as you work toward the top. 9. Use the width of the spray pattern to wash in a ...