Stimmen - 3, Durchschnittliche Bewertung: 4.3
(
)
)
|
Anleitung Zusammenfassung
The specifications, details, and photographs in this manual represent the Model H6247 as supplied when the manual was prepared. However, owing to Grizzly’s policy of continuous improvement, changes may be made at any time with no obligation on the part of Grizzly. Read the manual before operation. Become familiar with this machine, its safety instructions, and its operation before beginning any work. Serious personal injury may result if safety or operational information is not understood or followed. Foreword Contact Info Machine Data Motor ......................................... 110V, 1HP Blade Speed ................................ 200 RPM Dimensions ................... 161/2" x 81/2" x 15" Production ...............................485 lbs/hour Net Weight ........................................55 lbs. SET UP Unpacking Your machine left our warehouse in a carefully packed crate or box. If you discover the machine is damaged after you have signed for delivery, please immediately call Customer Service at (570) 5469663 for advice. Save the containers and all packing materials for possible inspection by the carrier or its agent. Otherwise, filing a freight claim can be difficult. When you are completely satisfied with the condition of the shipment, you should inventory the equipment. Inventory After you have unpacked the carton you should find the following. Model H6247 Inventory (Figure 1) A. Grinder Motor Housing (Not Shown) ... 1 B. Meat Pusher......................................... 1 C. Hopper ................................................. 1 D. Barrel ................................................... 1 E. Feed Screw.......................................... 1 F. Cutting Blade........................................ 1 G. Cutting Plate Fine ................................ 1 H. Cutting Plate Course............................ 1 I. Locking Ring.......................................... 1 J. Locking Knob........................................ 1 I B C D G F E J H Figure 1. Model H6247 inventory Model H6247 Meat Grinder -5- -- Assembling Grinding Head 1. Loosen the locking ring, and remove the barrel from the grinding motor housing. 2. Unscrew the lock ring and remove the cutting plate, cutting blade, and feed screw. Thoroughly sanitize the grinder head and throat, barrel, cutting plates, cutting blade, feed screw, lock ring, locking knob and hopper (refer to Proper Sanitization on page 9). 3. Before proceeding with assembly, wipe down the outside surface of grinder motor housing with a sanitized cloth. 4. After cleaning, assemble the grinder head by inserting the feed screw into the barrel with the vertical slot on the shaft projecting through the back of the barrel (Figure 2). Barrel Feed Screw Figure 2. Feed screw installation 5. Carefully slide the cutting blade on the square shaft on the front of the feed screw (Figure 3). Figure 3. Cutting blade installation 6. Choose one of the two cutting plates. 7. Slide the cutting plate over the shaft and the locking pin located at the bottom the barrel (Figure 4 ). Locking Pin Figure 4. Cutting plate installation 8. Screw the locking ring on the barrel clockwise to secure the assembly. Note–Use mild pressure to tighten. Overtightening can cause the cutting blade to bind against the cutting plate. -6- Model H6247 Meat Grinder 9. Twist the feed screw so the vertical slot on the feed screw aligns with the vertical shaft on the inside of the grinder head. 10. Slide the assembly into the grinder head. Use the pin on the side of the barrel as a guide into the slot. Note– The vertical slot on the back of the feed screw must align with the vertical shank inside the grinder head (Figure 5). Figure 5.Inserting assembly 11. Tighten the locking knob to secure the assembly to the grinding head. 12. Set the hopper into the throat of the grinder head (Figure 6). Figure 6.Inserting hopper Controls ON/OFF and REVERSE Switch (Figure 6): Figure 6.Switch location 1. Turn the switch to the right to turn the motor ON. 2. Turn the switch to the center position to turn the motor OFF. 3. The REVERSE feature is handy for clearing the cutting blade and cutting plate of meat. Turn the switch to the REVERSE position to REVERSE the direction of the cutting blade. WAIT UNTIL GRINDER HAS COME TO A COMPLETE STOP BEFORE REVERSING. The motor will only turn in reverse as long as the REVERSE switch is held in position. Model H6247 Meat Grinder -7 OPERATIONS Grinding The Model H6247 is designed for meat processing. DO NOT attempt to grind bone or hard foods like nuts or fibrous foods like celery or ginger. 1. Make sure all meat grinding parts are properly sanitized before beginning. (Refer to the Cleaning section on page 9). 2. Install the fine or course cutting plate. 3. Cut all meats into sizes that will easily fit into the hopper throat. 4. Plug in the grinder and turn it ON. 5. Use meat pusher to push meat down to the feed screw. DO NOT use any other utensil or stick fingers down the hopp...