Stimmen - 3, Durchschnittliche Bewertung: 4.7 ( )

Hersteller: Gilson Dateigröße: 168.39 kb Dateiname: cfd3d622-e06f-48d1-b676-013591560242.pdf Unterrichtssprache:

Hold the tilt handle and unlock the stop lever. Dump concrete to either side by tilting the tilt handle in the direction required. Before reloading the mixer, slowly pour a pail of water over the lip of the drum, permitting water to clean the inside of drum. When cleaned, dump water. Now you are ready for your next batch. CLEANING THE MIXER After each run of concrete has been poured, do the following: With the drum rotating, spray water into drum permitting the water to run down the inside and outside of drum. Add one shovel full of coarse aggregate and permit this mixture to scour the inside of drum for about two minutes. This practice will help keep the drum clean, which is essential in obtaining the best mixing result. Never permit concrete to harden on either the inside or outside of drum. EXTENSION CORDS-ELECTRIC MOTOR The following size extension cords should be used for this mixer: length of cord, up to 100 ft14 gauge wire; up to 200 ft-12 gauge wire; up to 300 ft – 10 gauge wire; up to 400 ft – 8 gauge wire. 4 3-LUBRICATION & STORAGE Each day before operating, lubricate at the following points: Engine/Motor – Refer to engine/motor operating instructions for all maintenance and lubrication instructions and requirements. GREASE FITTINGS : Refer to Fig. 2 Clean off grease fitting before greasing. Use pressure type grease gun. Grease lightly with general purpose grease (2 to 3 pumps). • Drum Shaft Bearings (where used) • Drive shaft Bearings • Tilt Wheel Shaft Bearings (where used) • Brake Lever Shaft (where used) OIL: Refer to Fig. 2 Use SAE 30 engine oil. • Yoke Tilt Mechanism STORAGE For short term storage, clean the mixer and store in a dry place. If the mixer is not to be used for an extended period of time, service mixer completely and store it in a dry place. 1. Refer to motor/engine instructions for storage instructions. 2. Cover exposed metal surfaces with a thin coat of SAE 30 engine oil. 3. Lubricate per instructions under LUBRICATION & STORAGE section. 5 4-REPLACEMENT DECALS #217728: Decal, Safety Instructions #5706: Decal, Gilson Name Plate #38257: Decal, Drum Rotation 6 7 CONCRETE MIXER PARTS LIST ITEM NO. PART NO. DESCRIPTION QTY. 1 1102 Grease Fitting 1 2 1183 Grip 1 3 19866 Bearing Cap 1 4 19902 Drum Assembly 1 19911 Blade Assembly 2 6 19913 Paddle Assembly 2 7 19914 Drum Shaft Assembly 1 8 214858 Belt Guard Cover 1 9 214907 Belt Guard Assembly 1 245948 Frame Assembly 1 11 245949 Yoke Assembly 1 12 245952 Tilt Handle 1 13 245956 Bushing Spacer 2 14 245977 Yoke Lock Tube 1 245978 Yoke Lock Assembly 1 16 245980 Pivot Tube 2 17 29209 Pulley 1 18 4959 Bushing 2 19 5450 Drum Shaft Spacer (Light) AS REQ'D 5452 Drum Shaft Spacer (Heavy) AS REQ'D 21 5498 Ring Gear 1 22 5523 Skid 2 23 5904 Grease Fitting (Drum) 1 24 763-40033 Drum Shaft Bearing 1 6007 Pinion Gear 1 26 6008 Drive Shaft 1 27 70448 Bolt, Carriage 3/8-16 x 3/4 8 28 70456 Bolt, Carriage 3/8-16 x 1 3/4 4 29 70073 Set Screw, Square Hd. 1/2-13 x 1 1 70090 Cap Screw, Hex Hd. 1/4-20 x 1/2 Plated 5 31 * Cap Screw, Hex Hd. 5/16-18 x 1 Plated 2 32 70249 Cap Screw, Hex Hd. 3/8-16 x 1 1/2 5 33 70343 Cap Screw, Hex Hd. 1/2-13 x 1 1/2 2 37 * Nut, Hex 1/4-20 Plated 5 70549 Nut, Hex 5/16-18 Plated 2 36 * Nut, Hex 3/8-16 20 37 * Nut, Hex 1/2-13 2 38 70701 Washer,Flat 5/16 Plated 2 39 70703 Washer,Flat 3/8 5 * Washer,Spring Lock 1/4 Plated 5 41 * Washer,Spring Lock 5/16 Plated 2 42 * Washer,Spring Lock 3/8 7 43 * Washer,Spring Lock 1/2 2 44 71017 Roll Pin 7/32 x 1 1/2 1 5269 Drum Shaft Bushing 2 46 * Bolt,Hex Hd. 3/8-16 x 3 1/4 2 47 760-40043 Pulley Spacer 1 *Common Hardware May Be Purchased Locally. 8 MIXERS ONE-YEAR WARRANTY This product is warranted to the original purchaser only, to be free of defects in material and workmanship under normal use, for one year from purchase date. Cleform Tool Corp. shall without charge for parts and labor, repair or replace such parts which are found to be defective. All transportation charges for replacement parts must be borne by the purchaser. For warranty service, the product must be delivered, with proof of purchase date, to the dealer of original purchase, or any factory authorized service dealer. The delivery of the unit must be made no later than 30 days after the expiration of the warranty period. If difficulty is encountered in having warranty work performed, contact the factory Service Department: CLEFORM TOOL CORP. 4343 EASTON ROAD ST. JOSEPH, MO 64503 800-253-3676 PHONE 888-253-3676 FAX Exclusion from this warranty: 1. The following items are not covered under the CLEFORM TOOL CORP. One year Warranty and are warranted by their respective manufacturer. a) Engines, including starters, generators, alternators and gear reducers. b) Enclosed gear transmissions. (Note: A copy of the warranty and service contact information for the above items is furnished with the individual product). 2. All consequential damages, including pickup and delivery of the unit, communication, mileage charges and/or rental of a ...

Herunterladen

Geben Sie zwei Ziffern: