Stimmen - 1, Durchschnittliche Bewertung: 3 ( )

Hersteller: KitchenAid Dateigröße: 418.62 kb Dateiname: Unterrichtssprache:

Unwrap the sliding cover and place into frame on top of the ice bin. Freestanding Refreshment Center WARNING Excessive Weight Hazard Use two or more people to move and install refreshment center. Failure to do so can result in back or other injury. Use a certified plumber to connect and install potable water supply and drain system to outdoor refreshment center according to local code requirements. 1. Check that you have adequate drain connections for the refreshment center. 2. Remove the faucet from the ice bin. 3. Install the faucet and securely fasten. A B D E C A. Faucet B. Brass escutcheon with “O” ring C. Sink D. Plastic washer E. Locking nut 4. Connect the plastic line from the water filter to the faucet connection and securely tighten. A B C D E A. Plastic tube insert B. Plastic ferrule C. Compression nut D. Plastic hose E. Filter 5. Install water inlet connection through hole provided in cabinet rear panel. A B C E D F A. Tubing from water filter (inlet) D. Brass locking nut B. Hose connector E. Inlet connector C. Hose connector nut F. Exterior side of mounting panel 6. Attach the plastic cold water hose from the water inlet connection to the inlet side of the filter. Use NSF or UPC listed water connection line for water supply to inlet connector. Potable water supply system must be connected to inlet connector according to local code requirements. A B C D A. Plastic hose B. Inlet connector C. Filter D. NSF or UPC listed water supply line or hose 7. Unwrap the sliding cover and place into frame on top of the ice bin. 8. Rotate the side shelves up into their locked position or leave down as needed. 9. Lock the front locking caster wheels to keep refreshment center from moving. REFRESHMENT CENTER CARE General Cleaning IMPORTANT: Always follow label instructions on cleaning products. Soap, water and a soft cloth or sponge are suggested first unless otherwise noted. To avoid weather damage use the accessory cover designed for the Outdoor Refreshment Center. STAINLESS STEEL Cleaning Method: Rub in direction of grain to avoid damaging stainless steel surface. ¦ Food spills should be cleaned as soon as possible. Spills may cause permanent discoloration. Use stainless steel cleaner and polish to clean spills. KitchenAid® Stainless Steel Cleaner and Polish Part Number 4396920 (not included) or KitchenAid® Stainless Steel Wipes Part Number 8212510 (not included): See “Assistance or Service” section to order. ¦ Liquid detergent or all-purpose cleaner: Rinse with clean water and dry with soft, lint-free cloth. ¦ Vinegar for hard water spots ¦ Use a glass cleaner to remove fingerprints. To avoid damage to stainless steel surfaces, do not use soap- filled scouring pads, abrasive cleaners, cleaners containing chlorine, Cooktop Polishing Creme, steel-wool pads, gritty washcloths or some paper towels. REFRESHMENT CENTER WATER FILTER ¦ Filter should be replaced every 6 to 12 months. To remove filter, turn filter counterclockwise ... turn and remove. To install filter, push in new cartridge and turn clockwise. REFRESHMENT CENTER EXTERIOR The quality of this material resists most stains and pitting, providing that the surface is kept clean and protected. Cleaning Method: ¦ Apply stainless steel polish to all areas before first use. Apply after each cleaning to avoid damage refreshment center exterior surface. ¦ Cleaning should always be followed by rinsing with clean, warm water. ¦ Use a metal polish or stainless steel brightener to remove fingerprints, water spots, oxidation, and food stains. Always follow the manufacturer’s directions. ¦ Wipe the surface completely dry with a soft cloth. Winterization of faucet and drain system When temperatures are below 35°F (1.7°C) for an extended period of time: 1. Turn off water source to sink. 2. Remove potable water supply system from connection and store it appropriately. 3. Remove filter from its connection and store filter inside in a warm dry area. 4. Disconnect ice bin and sink drain and ..." (6.4 mm) tubing from the filter connector and allow to drain. A A. Plastic hose 5. Cover refreshment center with accessory cover or tarpaulin. ASSISTANCE OR SERVICE Before calling for assistance or service, please check “Troubleshooting.” It may save you the cost of a service call. If you still need help, follow the instructions below. When calling, please know the purchase date and the complete model and serial number of your appliance. This information will help us to better respond to your request. If you need replacement parts If you need to order replacement parts, we recommend that you use only factory specified parts. These factory specified parts will fit right and work right because they are made with the same precision used to build every new KITCHENAID® appliance. To locate factory specified parts in your area, call us or your nearest KitchenAid designated service center. In the U.S.A. Call the KitchenAid Customer eXperience Center toll free: 1-800-422-1230. Our consultan...

Herunterladen

Geben Sie zwei Ziffern: