Stimmen - , Durchschnittliche Bewertung:
(
)
)
Hersteller: Harbor Freight Tools
Dateigröße: 170.24 kb
Dateiname: 92928.pdf
Unterrichtssprache:
Das Dokument wird geladen, bitte warten
 |
Das Dokument wird geladen, bitte warten
Anleitung Zusammenfassung
Keep the manual and invoice in a safe and dry place for future reference. Safety Warnings and Precautions WARNING: When using product, basic safety precautions should always be followed to reduce the risk of personal injury and damage to equipment. Read all instructions before assembly! 1. Watch weather conditions. If using the Car Canopy in windy areas be sure to anchor the legs with cement blocks, sand bags, or other means. This will keep the canopy from being carried away. Do not let snow accumulate on the canopy or it could collapse. 2. Avoid working alone. If an accident happens, an assistant can bring help. 3. Keep work area clean. Cluttered areas invite injuries. 4. Keep children away. Children must never be allowed in the work area. Do not allow them to play on or around the canopy. 5. Store idle equipment. When not in use, tools must be stored in a dry location to inhibit rust. Always lock up tools and keep out of reach of children. 6. Dress properly. Do not wear loose clothing or jewelry as they can be caught in moving parts. Protective, electrically nonconductive clothes and nonskid footwear are recommended when working. Wear restrictive hair covering to contain long hair. 7. Use eye and ear protection. Always wear ANSI approved impact safety goggles. 8. Do not overreach. Keep proper footing and balance at all times. Do not reach over or across electrical cables or frames. 9. Stay alert. Watch what you are doing, use common sense. Do not attempt to assemble when you are tired. 10. Check for damaged parts. Before using any tool, any part that appears damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for any broken parts or mounting fixtures; and any other condition that may affect proper operation. Any part that is damaged should be properly repaired or replaced by a qualified technician. 11. Replacement parts. When servicing, use only identical replacement parts. Use of any other parts will void the warranty. 12. Do not assemble if under the influence of alcohol or drugs. Read warning labels on prescriptions to determine if your judgment or reflexes are impaired while taking drugs. If there is any doubt, do not assemble the product. 13. Heavy, wet snow or extremely windy conditions could damage the Car Canopy. It is recommended that the Tarp be removed under these conditions to prevent damage to the Car Canopy or nearby property. Warning: The warnings, cautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator. Unpacking When unpacking, check to make sure that all parts are included. Refer to parts list on the last page of this manual. If any parts are missing or broken, please call Harbor Freight Tools at the number on the cover of this manual. Assembly 1. Place 17 Steel Tubes (1) on the ground as illustrated below. Caution: Be alert to possible wind damage; prolonged exposure to wind can cause fasteners and hardware to loosen as the frame flexes. The Portable Garage Car Canopy’s frame strength will be compromised if fasteners and hardware are not tight. Periodically check and make sure all fasteners and hardware are tight. Tubes, stakes, tie downs and rope should also be periodically checked to make sure the unit is always structurally rigid. 2. Connect 3-way and 4-way Tube Fittings (2 and 3) as shown below. At each junction, there is a hole through the side of the Fitting that lines up with the hole in the side of the Tube. Line up these holes on the inside of the structure and insert Self-tapping Screws (8), but tighten them only slightly at this time. 3. Drape Tarp (7) over assembled frame and secure the corners (first) onto the frame using the Ball Tie Downs (4) as shown in 4A, B, and C, below. 4. Once the corners are fastened, place the Ball Tie Downs through the balance of the metal eyelets as shown in the previous illustration, 4D. 5. Lift one side of the roof and slide in four Steel Tubes (1). Line up the holes in the Tubes with the holes in the Fittings and insert Self-tapping Screws (8), but tighten them only slightly at this time. When complete, do the same to the other side. See illustration to the right. 6. Insert the Nylon Base (5) onto each vertical leg. 7. Secure each Nylon Base to the ground Nylon Base (5) fits here. REV 09e using the T-Stakes (6). Tighten all Self-tapping Screws (8) securely. Maintenance 1. Periodically clean Tarp using mild soap and water. 2. Periodically disassemble and apply a light oil to the Steel Tubes to prevent rusting. Parts List Item # Description Qty 1 Steel Pipes 25 2 3-way Pipe Fitting 6 3 4-way Pipe Fitting 6 4 Ball Tie Down 48 5 Nylon Base 8 6 T-stakes 16 7 Tarp 1 8 Self-tapping Screws 42 PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND/OR DI...