Stimmen - 4, Durchschnittliche Bewertung: 4.5
(
)
)
|
Anleitung Zusammenfassung
6 “V” Design Crinkled Panels with LED Lighting Solar Panel Mount 9.33 Ft. Long Cord Batteries 3 Rechargeable “AA” 1.2V 500mAH (Included) Net Weight 31.1 Lbs. Maximum Weight Capacity 400 lb. Save This Manual You will need the manual for the safety warnings and precautions, assembly instructions, operating and maintenance procedures, parts list and diagram. Keep your invoice with this manual. Write the invoice number on the inside of the front cover. Keep the manual and invoice in a safe and dry place for future reference. GENERAL SAFETY RULES WARNING! READ AND UNDERSTAND ALL INSTRUCTIONSFailure to follow all instructions listed below may result in electric shock, fire, and/or serious injury. SAVE THESE INSTRUCTIONS Work Area Keep your work area clean and well lit. Dark areas invite accidents. Keep bystanders, children, and visitors away while assembling this product. Personal Safety. Replace or repair damaged or worn parts immediately. Do not exceed the max. weight capacity of 400 lb. Injury could occur if the bench is overloaded or unbalanced. Do not stand or climb on this bench. Do not set up this product if under the influence of alcohol or drugs. Read warning labels on prescriptions to determine if your judgement or reflexes are impaired while taking drugs. If there is any doubt, do not attempt to use this product. Use eye protection when assembling this product. Wear ANSI-approved safety impact eye goggles when assembling this product. Two adults are better at assembling this product. Be careful not to pinch fingers between the wooden seat slats. Do not allow children to play on this Park Bench. Children under 10 years of age should be accompanied by an adult. Do not let children stand on this Park Bench. The Bench could topple if overloaded or if weight is distributed unevenly. Do not let children or animals near the power source of this product. Check for damaged parts. Before using this product, carefully check that it will operate properly and perform its intended function. Check for damaged parts and any other conditions that may affect its operation. Service and maintenance should be performed by a qualified technician. LED lights are designed to last for a very long time. They should not need to be replaced. Do not force any part of the assembly and do not overtighten the bolts. Serious damage can occur. Use this product ONLY with the Solar Panel with Stake and Cord that accompanies this product. Do not use any other accessory. The Solar Panel with Stake must be placed where sunlight can recharge the Solar Lights. Placing it in a shady area or near a street light will cause the Solar Park Bench to not light up. When placing the Solar Panel with Stake into the ground, avoid any electrical wires or plumbing underground that are not visible. Avoid accidently cutting the electrical cord attached to the Solar Panel with Stake and to the Bench. This electric cord could cause tripping or be accidently cut by a lawn mower or gardening equipment. Avoid water around the cord. Always be cautious and avoid electrical shocks. Do not use if the cord is frayed or worn. If cord is damaged, contact a qualified technician to replace the electric cord. Use only on a flat, level surface that is capable of withstanding the weight of the Park Bench (31 lb.) and the Bench’s max weight capacity (400 lb.) The warnings, precautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator. Save these Instructions. Unpacking When unpacking, check to make sure that the item is intact and undamaged. If any parts are missing or broken, please call Harbor Freight Tools at the number on the cover of this manual as soon as possible. Assembly We suggest you assemble the unit on a soft surface to avoid damage to the finish. Attach the five wooden Seat Slats (3) onto the right and left Arm Rests (1) using the Screws (9) on the top side of the Slats and the Washers (8) and Nuts (10) on the underside. Hand tighten. See Figure 1. 57 & 8Figure 23Attach the Seat Brace (5) to the wooden Seat Slats (3) using the Tap Screws (7). Tighten all hardware after assembly. See Figure 2. Note: It may become necessary to enlarge the holes in the Seat Slats (3). Clear the hole of paint or varnish by sliding a bolt through the hole or using a drill (not included). 119, 8 & 10318, 9 &103Figure 1119, 8 & 10318, 9 &103Figure 1 7 07f Armrest (1) Screw (6) FIGURE 3Backrest (2) Attach the Back Assembly with LED Lights (2) to the Armrest (1), right and left. Use the four Screws (6) through the brackets on both Armrests (1) and through the Back Assembly (2). Tighten Screws. See Figure 3. To secure the Bench to the ground, hammer the Ground Nails (9) through the pre-drilled holes at the base of each leg. Make sure that when hammering nails i...