Stimmen - 4, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Note: You must follow all steps to properly assemble grill. Typical assembly: approximately 30 minutes. 4 Attach Top Hinges B x 2 F x 2 Hx 2Kx 2 3 Attach Lid Handle and Thermometer Assembly F x 2 Hx 2 Ix 2Kx 2 Assembly Instructions 6 Attach Locks Ax 4Ex 4 Gx 4Jx 4 5 Attach Bottom Hinges B x 4 F x 4 Hx 4Kx 4 7 Attach Grease Tray Supports A x 4Ex 4 Gx 4Jx 4 8 Insert Heat Plate Supports B x 4 F x 4 10 Attach Legs B x 6 F x 6 9 Assemble Legs Cx 6 D x 2 12 Attach Wind Guard and Regulator/Control Valve 11 Attach Burner and Igniter Wire C x 1 Assembly Instructions (continued) 13 Attach Lid L x 2 Mx 2 14 Insert Warming Rack 16 Insert Grease Plate 15 Insert Heat Plate and Cooking Grid Assembly Instructions (continued) Operating Instructions This grill is designed to operate with a one pound 7-3/8” high disposable / 16.4 oz. or 14.1 oz. propane gas tank (DOT 39 Cylinder). DO NOT ATTEMPT TO REFILL ANY ONE POUND (16.4 oz. or 14.1 oz.) PROPANE GAS TANKS! Connecting Gas Tank 1. Make sure the regulator/control valve is in the “LOCK OFF” position. (Figure 1a) 2. Lubricate the threads of the regulator valve with petroleum jelly, insert the gas tank into the regulator valve and hand-tighten firmly. (Figure 1b) 3. Test for leaks Checking for Leaks Burner Connection 1. Make sure the control valve is securely fastened to the burner. (Figure 2) If your unit was assembled for you, visually check the connection between the burner and control valve. WARNING: Failure to inspect this connection or follow these instructions could cause a fire or an explosion which can cause death, serious bodily injury, or damage to property. 2. If the burner pipe does not rest flush to the control valve, please contact 1.800.762.1142 for assistance. Regulator / 1# LP Gas Tank Connection 1. Make 2-3 oz. of leak solution by mixing one part liquid dishwashing soap with three parts water. 2. Make sure control knob is “OFF”. (Figure 3) 3. Spoon several drops of solution, or use squirt bottle, at the LP gas tank to regulator connection. (Figure 4) 4. Inspect the solution at the connection, looking for bubbles. If NO bubbles appear, the connections are secure. If bubbles appear, you have a leak. a. Loosen and retighten this connection, making sure the connection is secure. b. Retest with solution. If you continue to see bubbles after several attempts, disconnect propane source and contact 1.800.762.1142 for assistance. First Use 1. Make sure all labels, packaging and protective films have been removed from the grill. 2. Remove manufacturing oils before cooking on this grill for the first time, by operating the grill for at least 15 minutes on “HIGH” with the lid closed. This will “heat clean” the internal parts and dissipate odors. Lighting 1. Make sure all labels, packaging and protective films have been removed from the grill. 2. Open lid. Attempting to light the burner with the lid closed may cause an explosion! 3. Make sure there are no obstructions of airflow to the gas unit. Spiders and insects can nest within and clog the burner / venturi tube at the orifice. A clogged burner tube can lead to a fire beneath the appliance. 4. Control knob must be in the “LOCK OFF” position. (Figure 4) 5. Turn the control knob to “HIGH” 6. Press the Igniter button repeatedly to light burner. 7. If ignition does not occur in 5 seconds, turn burner control knob OFF, wait 5 minutes and repeat lighting procedure. 8. If igniter does not light burner, use a lit match to light burners manually. Access the burner through the hole in bottom bowl as indicated. (Figure 5 and 6) 9. Turn the grill to “LOW”, and position the lit match near side of the burner. Figure 1a Figure 1b LOCKOFFOFFLOWMEDHIGHPUSHTOTURN ON 17 Lock Lid Unlock Lid Figure 2 Figure 3 LOCKOFFOFFLOWMEDHIGHPUSHTOTURN ON Figure 4 XX Figure 5 Figure 6 Figure 7 1/2" 12.7 mm6.4mm0mm1/4" 0" Flame Troubleshooting Problem Possible Cause Prevention/Cure Burner will not light with match No gas flow. Check if LP gas tank is empty. Obstruction of gas flow. Clear burner. Spider webs or insect nest in burner tube. Clean burner tube. Burner ports clogged or blocked. Clean burner ports. Irregular flame pattern, flame does not run the full length of burner. Burner ports are clogged or blocked. Clean burner ports. Flame is yellow or orange New burner may have residual manufacturing oils. Burn grill for 15 minutes with the lid closed. Spider webs or insect nest in burner tube. Clean burner tube. Food residue, grease or seasoning salt on burner. Clean burner. Flame blow out High or gusting winds. Turn front of grill to face wind or increase flame height. Low on LP Gas. Replace LP gas tank. Flare-up Grease buildup. Clean grill. Excess fat in meat. Trim fat from meat before grilling. Excessive cooking temperature. Adjust (lower) temperature accordingly. Persistent grease fire. Grease trapped by food buildup around burner system. Turn knobs to “LOCK OFF POSITION.” Let fire burn out. Leave lid in closed position and let fire burn out. Afte...