Stimmen - 0, Durchschnittliche Bewertung: 0
(
)
)
|
Anleitung Zusammenfassung
This is the amount of memory located above 1 MB in the CPU's memory address map. 55 BIOS Setup 56 BIOS Features Setup Figure 3: BIOS Features Setup • 1st / 2nd / 3rd Boot Device Floppy Set your boot device priority to Floppy. LS/ZIP A: Set your boot device priority to LS/ZIP A:. ATAPI ZIP C: Set your boot device priority to ATAPI ZIP C:. CDROM Set your boot device priority to CDROM. SCSI Set your boot device priority to SCSI. NETWORK Set your boot device priority to NETWORK. IDE-0~IDE-3 Set your boot device priority to IDE-0~IDE-3. Disabled Disable this function. • S.M.A.R.T. for Hard Disks Enabled Enable S.M.A.R.T. Feature for Hard Disks. Disabled Disable S.M.A.R.T. Feature for Hard Disks. (Default Value) • IDE Boot Delay 1 Sec.~10 Sec. Set IDE Boot Delay to 1 Sec.~10 Sec. Disabled Disable this function. (Default Value) • Boot Up Num-Lock On Keypad is number keys. (Default Value) Off Keypad is arrow keys. AMIBIOS SETUP – BIOS FEATURES SETUP ( C ) 1999 American Megatrends, Inc. All Rights Reserved 1st Boot Device : Floppy 2nd Boot Device : IDE-0 3rd Boot Device : CDROM S.M.A.R.T. for Hard Disks : Disabled IDE Boot Delay : Disabled BootUp Num-Lock : On Floppy Drive Seek : Disabled Password Check : Setup Processor Serial Number : Disabled BIOS Flash Protection : Disabled ESC: Quit ^v> <: Select Item F1 : Help PU/PD+/-/ : Modify F5 :Old Values (Shift)F2:Color F6 : Load Fail-Safe Defaults F7 : Load Optimized Defaults 6VTX Motherboard • Floppy Drive Seek During POST, BIOS will determine if the floppy disk drive installed is 40 or 80 tracks. 360 type is 40 tracks while 720, 1.2 and 1.44 are all 80 tracks. Enabled BIOS searches for floppy disk drive to determine if it is 40 or 80 tracks. Note that BIOS can’t differentiate between from 720, 1.2 or 1.44 drive type as they are all 80 tracks. Disabled BIOS will not search for the type of floppy disk drive by track number. Note that there will not be any warning message if the drive installed is 360. (Default Value) • Password Check Please refer to the detail on P.74 Setup The user must enter correct password in order to access BIOS setup utility. (Default Value) Always The user must enter correct password in order to access the system and/or BIOS Setup. • •••• Processor Serial Number This item will show up when you install the Pentium® !!! processor. Enabled Pentium® !!! Processor Serial Number Feature. Disabled Disable this function. (Default value) • BIOS Flash Protection Enabled Enable BIOS Flash Protection. This will prevent BIOS Flash write after POST. Disabled To flash/upgrade BIOS on this MB, this item must be disable. We recommend this item to be set to “Disabled”. (Default Value) 57 BIOS Setup Chipset Features Setup We would not suggest you change the chipset default setting unless you really need it. AMIBIOS SETUP – CHIPSET FEATURES SETUP ( C ) 1999 American Megatrends, Inc. All Rights Reserved ***DRAM Timing*** Top Performance : Disabled SDRAM Timing by SPD : Disabled SDRAM CAS# Latency : 3 DRAM Frequency : Auto DRAM Integrity Mode : Disabled AGP Mode : 4X AGP Comp. Driving : Auto Manual AGP Comp. Driving : N/A AGP Aperture Size : 64MB USB Controller : All USB Port USB Legacy Support : Disabled ESC : Quit ^v> <: Select Item F1 : Help PU/PD+/-/ : Modify F5 :Old Values (Shift)F2:Color F6 : Load Fail-Safe Defaults F7 : Load Optimized Defaults Figure 4: Chipset Features Setup • •••• Top Performance If you wish to maximize the performance of your system, set “Top Performance” as “Enabled”. Disabled Disable this function. (Default Value) Enabled Top Performance Enable. • •••• SDRAM Timing by SPD Enabled Enable SDRAM Timing by SPD. Enable this function, the bios will set SDRAM Frequency/SDRAM CAS#/SDRAM Bank Interleave according to the SPD Data in SDRAM. Disabled Disable SDRAM Timing by SPD. (Default Value) • •••• SDRAM CAS# Latency 2 Set SDRAM CAS# Latency to 2. 3 Set SDRAM CAS# Latency to 3. 58 6VTX Motherboard 59 • DRAM Frequency Auto Set DRAM Frequency to Auto. 66Mhz Set DRAM Frequency to 66Mhz. 100Mhz Set DRAM Frequency to 100Mhz. 133Mhz Set DRAM Frequency to 133Mhz. • DRAM Integrity Mode Disabled Disable this function. (Default Value) ECC Single-bit error correction and multi-bit error detection. • AGP Mode 4X Set AGP Mode to 4X (Only if the AGP Card support 4X Rate). (Default Value) 1X Set AGP Mode to 1X. 2X Set AGP Mode to 2X. • AGP Comp. Driving Auto Set AGP Comp. Driving to Auto. (Default Value) Manual Set AGP Comp. Driving to Manual. If AGP Comp. Driving is Manual. Manual AGP Comp. Driving: 00~FF • AGP Aperture Size 4 MB Display AGP Aperture Size is 4MB. 8 MB Display AGP Aperture Size is 8MB. 16 MB Display AGP Aperture Size is 16MB. 32 MB Display AGP Aperture Size is 32MB. 64 MB Display AGP Aperture Size is 64MB. (Default Value) 128 MB Display AGP Aperture Size is 128MB. 256 MB Display AGP Aperture Size is 256MB. • USB Controller All USB Port Enable All USB Ports 0,1,2,3. (Default Value) Disabled Disable USB Controller. USB Port 0&1 Enable USB Ports 0&1...