Stimmen - 1, Durchschnittliche Bewertung: 3
(
)
)
|
Dieses Gerät hat auch andere Anweisungen:
Motherboards - GA-6WMM7 (287.04 kb)
Motherboards - GA-6WMM7 (1.07 mb)
Anleitung Zusammenfassung
· BIOS -Licensed AWARD BIOS. -AT CMOS Setup, BIOS / Chipset Setup, Green Setup, Hard Disk Utility included. · O.S. -Operation with MS-DOSa, Windowsa95, Windowsa98, WINDOWSa NT, OS/2, NOVELL and SCO UNIX. 2.3. ENVIRONMENT · Ambient Temp. -0°C to +50°C (Operating). · Relative Hum. -0 to +85% (Operating). · Altitude -0 to 10,000 feet (Operating). · Vibration -0 to 1,000 Hz. 2-2 Introduction · Electricity -4.75 V to 5.25 V. (Max. 20A current at 5V.) 1-3 Hardware Installation 3. HARDWARE INSTALLATION 3.1. UNPACKING The main board package should contain the following: • The 6WMM7 / 6WMM7-1 main board. • USER'S MANUAL for main board. • Cable set for IDE, Floppy devices, [COMB Port Cable (Optional)]. • CD for main board Utility. [IUCD (Bus Master + Sound Driver + LDCM + Utility), INTEL 82810 Driver.] The main board contains sensitive electric components, which can be easily damaged by static electricity, so the main board should be left in its original packing until it is installed. Unpacking and installation should be done on a grounded anti-static mat. The operator should be wearing an anti static wristband, grounded at the same point as the anti-static mat. Inspect the main board carton for obvious damage. Shipping and handling may cause damage to your board. Be sure there are no shipping and handling damages on the board before proceeding. After opening the main board carton, extract the system board and place it only on a grounded anti-static surface component side up. Again inspect the board for damage. Press down on all of the socket IC's to make sure that they are properly seated. Do this only on with the board placed on a firm flat surface. MDO NOT APPLY POWER TO THE BOARD IF IT HAS BEEN DAMAGED. 3-1 6WMM7/6WMM7-1 3.2. MAIN BOARD LAYOUT 6WMM7 6WMM7 ICH/ 82801 GMCH/ 82810 CPU AC97 FLOPPY IDE 1 IDE 2 J16 IR/CIR J5 BZ1 PS/2USB CPU FAN PWR FAN SYS FAN ATX POWER COM B VGA COM A JP3 JP13 GAME & AUDIO J9 JP28 TEL J3 J6 JP11 JP9 JP12 JP32 JP24 JP2 BAT BANK 0 BANK 1 AMR PCI 1PCI 2PCI 3 ISA 1 LPT JP1 YMF 744 Main BIOS Backup BIOS JP22 JP25 JP27 JP31 JP30 JP20 JP19 JP18 JP17 .Figure 3.1• 6WMM7-1 6WMM7-1 ICH/ 82801 GMCH/ 82810 CPU AC97 FLOPPY IDE 1 IDE 2IR/CIR J5 PS/2USB CPU FAN PWR FAN SYS FAN ATX POWER COM B VGA COM A JP3 JP13 GAME & AUDIO J9 TEL J3 J6 JP11 JP9 JP12 JP2 BAT BANK 0 BANK 1 AMR PCI 1PCI 2PCI 3 ISA 1 LPT JP1 YMF 744 Main BIOS Backup BIOS JP25JP31 JP20 JP19 JP18 JP17 .Figure 3.2• 3-2 Hardware Installation 3.3. QUICK REFERENCE FOR JUMPERS & CONNECTORS t I/O Ports Connector USB USB port. IDE1 For Primary IDE port. IDE2 For Secondary IDE port. PS/2 For PS/2 Mouse & Keyboard port. FLOPPY For Floppy port. COMB For Serial port2 (COM B){Support Modem Ring On}. COMA For Serial port1 (COM A){Support Modem Ring On}. LPT For LPT port. VGA For VGA Port. ATX Power For ATX Power Connector. GAME & Audio For GAME & MIC LINE-IN, LINE-OUT,TEL Port, AUX_IN, CD_IN, SPDIF OUT. t Socket 370 For CeleronTM Socket 370 Processor installed • IR : INFRARED Connector (IR / CIR) -- Function Option Pin No. Function 1 VCC 2 NC 3 IRRX 4 GND 5 IRTX 6 NC 7 CIRRX 8 VCC 9 NC 10 NC t CPU FAN : CPU cooling FAN Power Connector Pin No. Function 1 GND. 2 +12V 3 SENSE 3-3 6WMM7/6WMM7-1 t PWR FAN: Power FAN Connector Pin No. Function 1 GND. 2 +12V 3 SENSE t SYS FAN: System FAN Connector Pin No. Function 1 GND. 2 +12V 3 SENSE t J16:Buzzer Enable (Optional) Pin No. Function Open Internal Buzzer Disable Short Internal Buzzer Enable t J6 RING PWR ON :Internal Modem Card Ring PWR On Pin No. Function 1 Signal 2 GND t JP13 : Keyboard Power On Selection (Optional) Pin No. Function 1-2 short Enabled Keyboard power on. 2-3 short Disabled Keyboard power on(Default). t JP3 : CLEAR CMOS Pin No. Function 1-2 short Clear CMOS 2-3 short Normal operation (Default). t J9: CD Audio Line in Pin No. Function 1 Left 2 GND 3 GND 4 Right 3-4 Hardware Installation t JP25:AUX_IN Pin No. Function 1 AUX_L 2 GND 3 GND 4 AUX_R t J3:Wake on LAN Pin No. Function 1 +5V SB 2 GND 3 Signal • TEL : The connector for Modem with internal voice connector. Pin No. Function 1 Phone-in 2,3 GND 4 Mono-out t JP11:STR Enable Pin No. Function Close STR Enable Open STR Disable t JP12: Case Open Pin No. Function 1 Signal 2 GND t JP26 : CPU FREQ. Safe mode Pin No. Function 1-2 short Normal 2-3 short Safe Mode 1-2-3open Recovery t JP2: TABLE LOCK Pin No. Function Open Table LOCK (Default) Short Table Unlock. 3-5 6WMM7/6WMM7-1 t JP4: Timeout Reboot Pin No. Function Open Timeout Reboot. Short No Reboot. t JP27: Onboard H/W Audio (Optional) Pin No. Function 1-2 short Disabled H/W Audio. 2-3 short Enabled H/W Audio.(Default) t JP32/ JP22: USB Port Selection (Optional) Pin No. Function 1-2 short Front Panel USB Port Enabled. 2-3 short Back Front Panel USB Port Enabled. t JP24: Front Panel USB Port (Optional) Pin No. Function 1,4,5,10 NC 2 +5V 3,7,9 GND 6 USB P0+ 8 USB P0 t JP28: SPDIF (Optional) Pin No. Function 1 VCC 2 SPD OUT 3 GND t JP30: USB Keyboard wake-up (Optional) Pin No. Function 1-2 Disable ...