Stimmen - 0, Durchschnittliche Bewertung: 0
(
)
)
|
Anleitung Zusammenfassung
Also please make sure the pin assigment on the cable is the same as the pin assigment on the MB header. To find out if the chassis you are buying support front audio connector, please contact your dealer. 25 Panel and Jumper Definition Panel And Jumper Definition J7 : For 2X11 Pins Jumper REGN GD PWP. P. P+ S P KHD 1 1 1 GN (Green Switch) Open: Normal Operation Close: Entering Green Mode GD (Green LED) Pin 1: LED anode(+) Pin 2: LED cathode(.) HD (IDE Hard Disk Active LED) Pin 1: LED anode(+) Pin 2: LED cathode(.) SPK (Speaker Connector) Pin 1: VCC(+) Pin 2- Pin 3: NC Pin 4: Data(.) RE (Reset Switch) Open: Normal Operation Close: Reset Hardware System P+P.P.(Power LED) Pin 1: LED anode(+) Pin 2: LED cathode(.) Pin 3: LED cathode(.) PW (Soft Power Connector) Open: Normal Operation Close: Power On/Off Please note, Please connect the power LED, PC speaker, reset switch and power switch etc of your chassis front panel to the front panel jumper according to the pin assignment above. 26 8TX Motherboard J9 : Internal Buzzer Connector(Optional) 1 1 Enable Disable (Default) Pin No. Definition 2-3close Internal Buzzer Disable 1-2close Internal Buzzer Enable (Default) JP5 : Clear CMOS Function 1 1 Normal Clear CMOS (Default) Pin No. Definition 1-2 close Clear CMOS 2-3 close Normal (Default) Please note, You may clear the CM OS data to its default values by this jum per 27 Panel and Jumper Definition JP6 : Safe mode / Recovery / Normal 1 1 1 Normal Safe Recovery (Default) Mode Pin No. Definition 1-2close Normal(Default) 2-3close Safe mode NC Recovery Please note, Sometime the system can not start up due to the setting in the CMOS/BIOS, to restore the CMOS/BIOS setting back to its safe setting the jumper can be set to 2-3. Once your system can start up you can set the jumper back to its normal position 1-2. JP7 : Timeout Reboot Function 1 1 Timeout Reboot No Reboot on Timeout (Default) Pin No. Definition 1-2close Timeout reboot 2-3close No Reboot on timeout (Default) Please note, This MB supports time out reboot function. If the system lock up, the reboot timer will start to count. Once the timer counts to a specific value the system will reboot automatically. When this event happens the system will boot up in safe BIOS mode. 28 8TX Motherboard JP8 : PCI Sound Function Selection 1 1 Enable Disable (Default) Pin No. Definition 1-2 close PCI Sound Enable(Default) 2-3 close PCI Sound Disable JP10 : Top Block Lock 1 1 Lock Unlock (Default) Pin No. Definition 1-2close Top Block Unlock (Default) 2-3close Top Block lock Please note, To upgrade BIOS on this M/B,JP10 must be set to 1&2. 29 Panel and Jumper Definition JP11 : BIOS Write Protection 1 1 Normal Write (Default) Protection Pin No. Definition 1-2close Write Protection 2-3close Normal (Default) Please note, To flash/upgrade BIOS on this MB JP 11 m ust be set to 2 & 3. We recomm end JP 11 to be set to 1 & 2, whenever user does not need to flash/upgrade the BIOS. JP13 : CNR Select 1 Pin No. Definition (Onboard CDOEC) CNR Card 1-2close Primary Secondary 2-3close AC’97 Disabled (Disabled Onboard CODEC) Primary Please note: 8TX: If M/B has hardware audio (CT5880), your modem riser has been set to“Primary” automatically. No Jumper JP13 for 8TX 8TX: JP13: 1-2 close: If you use software audio(onboard CODEC only), your modem riser must be “Secondary”. JP13: 2-3 close: If you don’t use onboard software audio, your audio/modem riser must be “Primary”. Mainboard’s software audio will be disabled. There are two types of CNR card in the market, Primary and secondary. If your CNR card is primary, JP13 should be set to 2-3, if you have secondary CNR cardJP 13 should be set to 1-2. Warning! If Primary CNR card is used, on-board CODEC will be disabled. 30 8TX Motherboard JP14 : PS/2 Keyboard Power On 1 1 Enable Disable (Default) Pin No. Definition 1-2 close PS/2 Keyboard Power on Enabled 2-3 close PS/2 Keyboard Power on Disabled (Default) Please note, Please note, PS/2 keyboard power on will enable user to power onhis computer by pressing the designated key/keys on the PS/2 keyboard. Toenable PS/2 keyboard power on, set jumper JP14 to 1-2, and then enable thePS/2 keyboard power on function to assign the key/keys of your choice inside the BIOS setup Menu. JP16 : Case Open 1 Pin No. Definition 1 Signal 2 GND 31 Panel and Jumper Definition JP17 : STR Selection 1 1 Disabled Enabled (Default) Pin No. Definition 2-3close STR Disabled (Default) 1-2close STR Enabled JP20 : Rear USB Device Wake up Selection (USB Connector .. CN7) CN7 1 1 Normal Enable (Default) Pin No. Definition 1-2 close Rear USB Device Wakeup Enabled 2-3 close Normal (Default) Please note, To use “USB KB/MS Wakeup from S3” function, set BIOS setting “USB KB/MS Wake up from S3” to ENABLED and enable jumpers JP20&JP17. To prevent user confusion, it is recommended to enable, jumper JP21 (Front USB Device wake-up function). *(Power on the computer and as soon as memory counting starts, press . You will enter BIOS Setup. Select...