Stimmen - 0, Durchschnittliche Bewertung: 0
(
)
)
|
Anleitung Zusammenfassung
8. Install related driver from the operating system. Please carefully pull out the small white- drawable bar atthe end of the AGP slotwhen you try to install/ Uninstall the AGP card. Please align the AGP card to the onboard AGP slot and press firmly down on the slot . AGP Card Make sure your AGP card is locked by the small white-drawable bar. GA-8SG800 Series Motherboard -12 Step 4: Connect ribbon cables, cabinet wires, and power supply Step 4-1: I/O Back Panel Introduction uvwxy English • PS/2 Keyboard and PS/2 Mouse Connector PS/2 Mouse Connector (6 pin Female) PS/2 Keyboard Connector (6 pin Female) • USB Connector USB 0 USB 1 OThis connector supports standard PS/2 keyboard and PS/2 mouse. • Before you connect your device(s) into USB connector(s), please make sure your device(s) such as USB keyboard,mouse, scanner, zip, speaker..etc. Have a standard USB interface. Also make sure your OS supports USB controller. If your OS does not support USB controller, please contact OS vendor for possible patch or driver upgrade. For more information please contactyour OS or device(s) vendors. -1 3 -Har dware Installatio n Proc ess • Parallel Port and Serial Ports (COMA/COMB) English Parallel Port (25 pin Female) C O M A C O M BSerialPort (9 pin Male) • Game /MIDI Ports Joystick/ MIDI (15 pin Female) • Audio Connectors M IC In Line Out (Front Speaker) Line In(Rear Speaker) (Cen ter and Subwoo fer) OThis connector supports 2 standard COM ports and 1 Parallel port. Device like printer can be connected to Parallel port; mouse and modem etc can be connected to Serialports. OThis connector supports joystick, MIDI keyboard and other relate audio devices. OAfter install onboard audio driver, you may connect speaker to Line Out jack, micro phone to MIC In jac k. Device like CD-ROM , walkman etc can be connected to Line-In jack. Please note: You are able to use 2-/4-/6-channel audio feature by S/W selection. If you want to enable 6-channel function, you have 2 choose for hardware connection. Method1: Connect "Front Speaker" to "Line Out" Connect "Rear Speaker" to "Line In" Connect "Center and Subwoofer" to "MIC Out". Method2: You can refer to page 19, and contact your nearest dealer for optional SUR_CEN cable. If you want the detail information for 2-/4-/6-channel audio setup installation, please refer to page 67. GA-8SG800 Series M otherboard -1 4 Step 4-2: Connectors Introduction 4 1 5 6 11 13 18 14 12 17 3 10 7 9 15 2 16 8 1) CPU_FAN 10) BAT 2) SYS_FAN 11) F_AUDIO 3) NB_FAN 12) SUR_CEN 4) ATX_12V 13) CD_IN 5) ATX 14) AUX_IN 6) IDE1/IDE2 15) SPDIF 7) FDD 16) F_USB1/F_USB2 8) PWR_LED 17) 1394 9) F_PANEL 18) CI English -1 5 -Har dware Installatio n Proc ess EnglishEnglish 1) CPU_FAN (CPU FAN Connector) Sense +12V 1 G N D 2) SYS_FAN (System FAN Connector) 1 Sense G N D +12V 3) NB_FAN (Chip FAN Connector) 1 +12V G N D 4) ATX_12V (+12V Power Connector) +12V G N D 43 G N D 1 2 +12V • Please note, a proper installation of the CPU cooler is essential to prevent the CPU from running under abnormalcondition or damaged by overheating.The CPU fan connector supports Max. current up to 600 mA. • This connector allows you to link with the cooling fan on the system case to lower the system temperature. • If you installed wrong direction, the Chip Fan will not work. Sometimes will damage the Chip Fan. (Usually black cable is GND) OThis connector (ATX_12V) supplies the CPU operation voltage (Vcore). If this " ATX_12V connector" is not connected, system cannot boot. GA-8SG800 Series M otherboard -1 6 5)ATX(ATX Power) • AC power cord should only be connected to your power supply unit after ATX power cable and other related devices are firmly connected to themainboard. 20 +12V 1 V C C 5V SB (Sta nd by +5V) V C C Power Good -5V G N D G N D V C C G N D G N D G N D V C C PS-ON(Soft On/O ff) G N D G N D 3.3V -12V 3.3V 3.3V 6) IDE1/ IDE2 [IDE1 / IDE2 Connector(Primary/Secondary)] • Important Notice: Please connect first harddisk to IDE1 and connect CDR OM to IDE2. The red stripe of the ribbon cable must be the same side with the Pin1. ID E1 7) FDD (Floppy Connector) • Please connect the floppy drive ribbon cables to FDD. It supports 360K,1.2M, 720K, 1.44M and 2.88M bytes floppy disk types. The red stripe of the ribbon cable must be the same side with the Pin1. 1 1 ID E2 1 English -1 7 -Har dware Installatio n Proc ess EnglishEnglish 8) PWR_LED • PWR_LED is connect with the system power indicator to indicate whether the system is 1 MPD+ MPDMPDon/ off. Itwill blink when the system enters suspendmode. If you use dual color LED, power LED willturn toanother color. 9) F_PANEL (2x10 pins connector) MSG+ MSG PW+ PW SPK+ SPK 2 20 1 19 1 1 1 11 HD+ HD RES RES+NC HD (IDE Hard Disk Active LED) (Blue) Pin 1: LED anode(+) Pin 2: LED cathode(-) SPK (Speaker Connector) (Amber) Pin 1: VCC(+) Pin 2-Pin 3: NC Pin 4: Data(-) RES (Reset Switch) (Green) Open: Normal Operation Close: Reset Hardware System PW (Soft Power Connector) (Red) Open: Normal Operation Close: Power ...