Stimmen - 0, Durchschnittliche Bewertung: 0
(
)
)
|
Anleitung Zusammenfassung
GA-8GEM667K Motherboard - 4 Chapter 1 Introduction Chapter 1 Introduction Features Summary English Form Factor • 24.4cm x 22cm Micro-ATX size form factor, 4 layers PCB. CPU • Socket 478 for Intel® Micro FC-PGA2 Pentium® 4 processor • Support Intel ® Pentium ® 4 (Northwood, 0.13 m) processor • Support Intel ® Pentium ® 4 Processor with HT Technology • Intel Pentium®4 400/533MHz FSB • 2nd cache depends on CPU Chipset • Chipset Intel 845GE HOST/AGP/Controller • ICH4 I/O Controller Hub Memory • 2 184-pin DDR DIMM sockets • Supports DDR333/DDR266 DIMM • Supports up to 2GB DRAM (Max) • Supports only 2.5V DDR DIMM I/O Control • IT8712 Slots • 1 AGP slot 4X (1.5V) device support • 3 PCI slot supports 33MHz & PCI 2.2 compliant On-Board IDE • 2 IDE bus master (UDMA33/ATA66/ATA100) IDE ports for up to 4 ATAPI devices • Supports PIO mode3,4 (UDMA 33/ATA66/ATA100) IDE & ATAPI CD-ROM On-Board Peripherals • 1 Floppy port supports 2 FDD with 360K, 720K,1.2M, 1.44M and 2.88M bytes. • 1 Parallel port supports Normal/EPP/ECP mode • 2 Serial ports (COMA&COMB);1 VGA Port • 6 USB 2.0/1.1 ports (2 x Rear, 4 xFront by cable) • 1 Front Audio Connector • 1 IrDA connector for IR/CIR • 1 Front Audio connector • !!!!!Due to (Intel 845PE/GE/GV) chipset architecture limitation, DDR 333 memory module is only supported when using FSB 533 Pentium 4 processor. A FSB 400 Pentium 4 processor ...... will only support DDR 266 memory module to be continued...... -5 - Introduction English Hardware Monitor • CPU/System Fan Revolution detect • CPU/System Fan Fail Warning • CPU Overheat Warning • System Voltage Detect On-Board VGA • Built in Intel 845GE Chipset On-Board Sound • Realtek ALC650 CODEC • Line Out / 2 front speaker • Line In / 2 rear speaker(by s/w switch) • Mic In / center& subwoofer(by s/w switch) • SPDIF out • 1 Buzzer • CD In / AUX In / Game port On-Board LAN • Intel Kinnereth-R LAN PHY PS/2 Connector • PS/2 Keyboard interface and PS/2 Mouse interface BIOS • Licensed AWARD BIOS, 2M bit Flash ROM • Supports Q-Flash Additional Features • PS/2 Keyboard power on by password • PS/2 Mouse power on • External Modem wake up • STR(Suspend-To-RAM) • Wake on LAN (WOL) • AC Recovery • Poly fuse for keyboard over-current protection • USB KB/Mouse wake up from S3 • Supports @BIOS • Supports EasyTune 4 Overclocking • Over Clock (DDR/AGP/CPU) by BIOS Please set the CPU host frequency in accordance with your processor’s specifications. We don’t recommend you to set the system bus frequency over the CPU’s specification because these specific bus frequencies are not the standard specifications for CPU, chipset and most of the peripherals. Whether your system can run under these specific bus frequencies properly will depend on your hardware configurations, including CPU, Chipsets,SDRAM,Cards….etc. GA-8GEM667K Motherboard - 6 HT functionality requirement content "Enabling the functionality of Hyper-Threading Technology for your computer system requires all of the following platform components: - CPU: An Intel® Pentium 4 Processor with HT Technology - Chipset: An Intel® Chipset that supports HT Technology - BIOS: A BIOS that supports HT Technology and has it enabled - OS: An operation system that has optimizations for HT Technology English -7 -Introduction GA-8GEM667K Motherboard - 8 - English GA-8GEM667K Motherboard Layout .. 2X_DET Kinnereth-R SPDIF_O F_AUDIO CI GA-8GEM667K KB_MS COMA LPT USB SOCKET478 CPU_FAN ATX FDD VGA IDE2 IDE1 PWR_LED PCI3 F_USB2 BIOS F_PANEL SYS _FAN ICH4 F_USB1 GAME LINE_IN MIC_IN LINE_OUT ATX_12V AGP DDR2 DDR1 845GE BAT PCI1 PCI2 IT8712 CODEC IR_CIR WOL CLR_PWD LAN BUZZER COMB CD_IN SUR_CEN - 9 - Hardware Installation Process English .. To set up your computer, you must complete the following steps: Step 1- Install the Central Processing Unit (CPU) Step 2- Install memory modules Step 3- Install expansion cards Step 4- Connect ribbon cables, cabinet wires, and power supply Step 5- Setup BIOS software Step 6- Install supporting software tools Chapter 2 Hardware Installation Process Step 4 Step 1 Step 2 Step 4 Step 4 Step 3 Step 1 Step 1: Install the Central Processing Unit (CPU) Step1-1 : CPU Installation English Angling the rod to 650 Socket Actuation Lever 1. Angling the rod to 65-degree maybe feel 2. Pull the rod to the 90-degree directly. a kind of tight, and then continue pull the rod to 90-degree when a noise “cough” made. Pin1 indicator 3. CPU Top View Pin1 indicator 4.Locate Pin 1 in the socket and look for a (golden) cut edge on the CPU upper corner. Then insert the CPU into the socket. • !!!!! Please make sure the CPU type is supported by the motherboard. • !!!!! If you do not match the CPU socket Pin 1 and CPU cut edge well, it will cause improper installation. Please change the insert orientation. GA-8GEM667K Motherboard - 10 Step1-2 : CPU Heat Sink Installation English 1. Hook one end of the cooler bracket to the CPU socket first. 2.Hook the other end of the cooler bracket to the CPU socket. • !!!!!Please use Intel app...