Stimmen - 0, Durchschnittliche Bewertung: 0
(
)
)
|
Anleitung Zusammenfassung
• USB/ LAN Connector • Before you connect your device(s) into USB connector(s), please make sure your device(s) such as USB keyboard, mouse, scanner, zip, speaker..etc. Have LAN a standard USB interface. Also make sure your OS supports USB controller. If your OS does not support USB 0 USB controller, please contact OS vendor for possible USB 1 patch or driver upgrade. For more information please contact your OS or device(s) vendors. GA-8PE800 Ultra / Pro(-R) M otherboard -18 Step 4-2 :Connectors & Jumper Setting Introduction 1 3 5 12 2 25 11 10 7 4 16 21 817 27 19 23 20 6 22 15 24 18 13 14 9 26 1) ATX_12V 15) IR/CIR 2) ATX Power 16) F_USB1/F_USB2 3) CPU_FAN 17) WOL• 4) SYS_FAN 18) SCR 5) PWR_FAN 19) F1_1394/F2_1394 6) NB_FAN 20) SPDIF_IO 7) IDE1/IDE2 21) F_AUDIO 8) IDE3/IDE4 v,• 22) CD_IN 9) S_ATA1/S_ATA2 • 23) AUX_IN 10) FDD 24) SUR_CEN 11) F_PANEL 25) CI 12) LED2 26) CLR_PWD 13) PWR_LED 27) BATTERY 14) 2X_DET * For GA-8PE800 Pro Only tFor GA-8PE800 Pro-R Only vFor GA-8PE800 Ultra Only -19 -Hardware Installation Process English EnglishEnglish 1) ATX_12V ( +12V Power Connector) This connector (ATX _12V) suppliesthe CPU operation voltage (Vcore). If this " ATX_ 12V connector" is not connected, system cannot boot. 4 3 2 1 Pin No. Definition 1 GND 2 GND 3 +12V 4 +12V 2) ATX_POWER (ATX Power) AC power cord should only be connected to your power supply unit after ATX power cable and other related devices are firm ly connected to the m ainboard. 20 111 10 Pin No. Definition 1 3. 3V 2 3. 3V 3 GND 4 VCC 5 GND 6 VCC 7 GND 8 Power Good 9 5V SB( stan d b y +5 V) 10 +12V 11 3. 3V 12 -12V 13 GND 14 PS _O N ( softO n/ Off) 15 GND 16 GND 17 GND 18 -5 V 19 VCC 20 VCC GA-8PE800 Ultra / Pro(-R) M otherboard -20 3) CPU_FAN (CPU FAN Connector) Please note, a proper installation of the CPU cooler is essential to prevent the CPU from running under abnorm al condition or dam aged by overheating.The CPU fan connector supports Max. current up to 600 m A. 1 Pin No. Definition 1 GND 2 +12V 3 Sense 4) SYS_FAN (System FAN Connector) This connector allows you to link with the cooling fan on the system case to lower the system temperature. 1 Pin No. Definition 1 GND 2 +12V 3 Sense -21 -Hardware Installation Process English EnglishEnglish 5) PWR_FAN (Power Fan Connector) This connector allows you to link with the cooling fan on the system case to lower the system temperature. 1 Pin No. Definition 1 GND 2 +12V 3 Sense 6) NB_FAN If you installed wrong direction, the Chip Fan will not work. Som etim es will dam age the Chip Fan. (Usually black cable is GND) 1 Pin No. Definition 1 VCC 2 GND GA-8PE800 Ultra / Pro(-R) M otherboard -22 7) IDE1/ IDE2(IDE1/IDE2 Connector) Please connect first harddisk to IDE1 and connect CDROM to IDE2. The red stripe of the ribbon cable m ust be the sam e side with the Pin1. 40 39 12 IDE2 IDE1 8) IDE3 /IDE4 (RAID/ATA133,Green Connectorr)v,• The ra d stripe of the ribbn c able m ust be the sam e side with the Pin1. If you wish to use IDE3 and IDE4, please use it in unity with BIOS (either RAID or ATA133). Then, install the correct driver to have proper operation. For details, please refer to the RAID m anual. (BIOS Defa ult Valu e :ATA, If you w ant to u se RAID function, please c hange “Integr ated Peripherals -RAID Controller Fun ction “to “R AID”) ID E4 ID E3 39 40 2 1 * For GA-8PE800 Pro Only tFor GA-8PE800 Pro-R Only vFor GA-8PE800 Ultra Only -23 -Hardware Installation Process English EnglishEnglish 9) S_ATA1/S_ATA2 (SerialATAConnector)• You can connect the Serial ATA device to this connector, it provides you high speed transfer rates (150MB/sec). 1 7 Pin No. Definition 1 GND 2 TXP 3 TXN 4 GND 5 RXN 6 RXP 7 GND 10)FDD (Floppy Connector) Please connect the floppy drive ribbon cables to FDD. It supports 360K,720K,1.2M ,1.44M and 2.88Mbytes floppy disk types. The red stripe of the ribbon cable m ust be the sam e side with the Pin1. 1 34 2 33 * For GA-8PE800 Pro Only tFor GA-8PE800 Pro-R Only vFor GA-8PE800 Ultra Only GA-8PE800 Ultra / Pro(-R) M otherboard -24 11) F_PANEL (2x10 pins connector) PW MPD MPD + Please connect the power LED, PC peaker, reset switch and power switch etc of your chassis front panel to the F_PANEL connector according to the pin assignm ent above. Sp ea ke r Co n ne cto r So f t Po we r Co n n e cto r Me s s a g e L E D / P o w e r / Sle e p L ED 1 HD + S PK 19 HDS PK + 20 2 1 11 1 1 PW + R SE + RS EN C ID E H a rd Di sk Ac tiv e L ED Re s e t Swi tch HD (IDE Hard Disk Ac tive LED) (Blue) Pin 1: LED anode(+) Pin 2: LED c athode(-) SPK(Speaker Connector) (Amber) Pin 1: VCC(+) Pin 2-Pin 3: NC Pin 4: Data(-) RES (Reset Switc h) (Green) Open: Norm al Operation Close: Reset Hardware System PW (Soft Power Connec tor) (Red) Open: Norm al Operation Close: Power On/Off M SG(M essage LED/Power/ Sleep LED)(Yellow) Pin 1: LED anode(+) Pin 2: LED c athode(-) NC( Purple) NC 12) LED2 Do not remove m em ory modules while DIM M LED is on. It m ight cause short or other unexpected dam ages due to the 2.5V st...