Stimmen - , Durchschnittliche Bewertung: ( )

Anleitung Gigabyte, modell GA-8KNXP Ultra-64

Hersteller: Gigabyte
Dateigröße: 328.05 kb
Dateiname:

Unterrichtssprache:

Das Dokument wird geladen, bitte warten

HerunterladenSchließen

Das Dokument wird geladen, bitte warten

HerunterladenSchließen

Dieses Gerät hat auch andere Anweisungen:

Motherboards - GA-8KNXP Ultra-64 (435.59 kb)

Motherboards - GA-8KNXP Ultra-64 (5.65 mb)

Motherboards - GA-8KNXP Ultra-64 (5.6 mb)

(1) Installing SATA hard drive(s) in your system Attach one end of the SATA signal cable to the rear of the SATA hard drive and the other end to available SATA port(s) on the motherboard (If there are more than one SATA controller on your motherboard, you may check the name of the SATA connector to identify the SATA controller for the connector. For example, SATA0_SII/SATA1_SII is controlled by the Sil3114 controller). Then connect the power connector from your power supply to the hard drive. "*" Skip this step if you do not want to create RAID array on the SATA controller SATA Hard Drive Configurations (Sil3114) -2 (2) Configuring SATA controller mode and boot sequence in BIOS Setup You have to make sure whether the SATA controller is configured correctly in system BIOS Setup and set BIOS boot sequence for the SATA hard drive(s). Step 1: Turn on your computer and press Del to enter BIOS Setup during POST (Power-On Self Test). In BIOS Setup menu, go to Integrated Peripherals and assure Onboard H/W SATA is enabled. If you want to create RAID, set the H/W SATA Function item to RAID (RAID by default) (Figure 1). Change the H/W SATA Function item to BASE if you do not want to create RAID. CMOS Setup Utility-Copyright (C) 1984-2004 Award Software Integrated Peripherals • ........: Move Enter: Select +/-/PU/PD: Value F10: Save ESC: Exit F1: General Help F3: Language F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults Figure 1 The BIOS Setup menus described in this section may not show the exact settings for your motherboard. The actual BIOS Setup menu options you will see shall depend on the motherboard you have and the BIOS version . -3 -SATA Hard Drive Configurations (Sil3114) ..• • ..• • Ac Step 2: Select Hard Disk Boot Priority under the Advanced BIOS Features menu. In the Hard Disk BootAe Priority submenu, select the model of the SATA hard drive onto which you want to install Microsoft Windows 2000/XP (Figure 2). ¤¤ CMOS Setup Utility-Copyright (C) 1984-2004 Award Software Hard Disk Boot Priority ¤a Figure 2 Step 3: Set First Boot Device under the Advanced BIOS Features menu to CD-ROM to boot from CD-ROM drive after system restarts (Figure 3). CMOS Setup Utility-Copyright (C) 1984-2004 Award Software Advanced BIOS Features • ........: Move Enter: Select +/-/PU/PD: Value F10: Save F3: Language F5: Previous Values F6: Fail-Safe Defaults ESC: Exit F1: General Help F7: Optimized Defaults • Figure 3 Step 4: Save and exit BIOS Setup. SATA Hard Drive Configurations (Sil3114) -4 (3) Configuring RAID set in RAID BIOS Enter the RAID BIOS setup utility to configure a RAID array. Skip this step and proceed to Section 4 if you do not want to create RAID. Step 1: After the POST memory test begins and before the operating system boot begins, look for a message which says "Press or to enter RAID utility"(Figure 4). Hit the CTRL+ S or F4 key(s) to enter the RAID BIOS setup utility. If you cannot enter the RAID BIOS correctly, assure that your SATA drives are properly installed. Figure 4 Step 2 After you enter the RAID Configuration Utility, a screen similar to that below will appear (Figure 5). You can use the UP or DOWN ARROW key to highlight through choices. Highlight an item that you want to execute and press ENTER. .... Figure 5 -5 -SATA Hard Drive Configurations (Sil3114) Ac Step 3: Create RAID set: Ae Select Create RAID set and press ENTER, and the RAID type selection menu will appear (Figure 6). Use the UP or DOWN ARROW key to select a RAID type that you want to create and press ENTER. ¤¤ The options include RAID 0, RAID 1, RAID10, and SPARE DRIVE. ¤a .... Figure 6 Step 4: After the selection of a RAID type, select Auto configuration or Manual configuration (Figure 7). If Auto configuration is selected, BIOS will automatically assign RAID member drives and set the chunk size of Striped Sets to 64KB. If Manual configuration is selected, you can manually change the chunk size (from 4K to 128K) and then assign the drives to be used in the RAID array. .... Figure 7 SATA Hard Drive Configurations (Sil3114) -6 Step 5: After finishing all the settings of a RAID set and press ENTER, you should see the prompt "Are You Sure? " Press Y to confirm or N to cancel. After the configuration is completed, the lower screen will display the RAID set information, including RAID type and array size (Figure 8). .... Figure 8 If you want to remove one or more RAID sets, select the Delete RAID set item (Figure 9) in Main Menu. Press ENTER and follow the on-screen instructions to delete the RAID set. .... Figure 9 After completing the configuration, press CTRL+E to exit the RAID Configuration Utility. Now, you can proceed to the installation of the SATA driver and operating system. -7 -SATA Hard Drive Configurations (Sil3114) Ac (4) Making a SATA controller driver disk To install Windows 2000/XP onto a SATA hard drive on the Sil3114 controller successfully, you need Ae to install required driver for the SATA contro...