Stimmen - 0, Durchschnittliche Bewertung: 0
(
)
)
|
Dieses Gerät hat auch andere Anweisungen:
Anleitung Zusammenfassung
8. If you are uncertain about any installation steps or have a problem related to the use of the product, please consult a certified computer technician. Instances of Non-Warranty 1. Damage due to natural disaster, accident or human cause. 2. Damage as a result of violating the conditions recommended in the user manual. 3. Damage due to improper installation. 4. Damage due to use of uncertified components. 5. Damage due to use exceeding the permitted parameters. 6. Product determined to be an unofficial Gigabyte product. -9 - Hardware Installation English 1-2 Feature Summary CPU • Supports the latest Intel® Pentium® 4 LGA775 CPU • Supports 800/533MHz FSB • L2 cache varies with CPU Chipset • Northbridge: Intel® 915P Express Chipset • Southbridge: Intel® ICH6 • Supported on the Win 2000/XP operating systems Memory • 2 DDR DIMM memory slots (supports up to 2GB memory) • Supports 2.5V DDR DIMM • Supports dual channel DDR 400/333 DIMM • 2 DDR II DIMM memory slots (supports up to 2GB memory) • Supports 1.8V DDR II DIMM • Supports dual channel DDR II 600(Note 1)/533/400 DIMM (Note: Mixed mode, populating DDR and DDR II memory modules simultaneously is not supported.) Slots • 1 PCI Express x 16 slot • 2 PCI Express x 1 slots • 3 PCI slots IDE Connections • 1 IDE connection (UDMA 33/ATA 66/ATA 100), allows connection of 2 IDE devices(IDE1) -Supported on the Win 2000/XP operating systems • Built-in VT6410 chipset -2 IDE connection (UDMA 33/ATA 66/ATA 100/ATA 133), compatible with RAID, allows connection of 4 IDE devices(IDE2,IDE3) (Note 2) -Supports disk striping (RAID 0) or disk mirroring (RAID 1) or striping + mirroring (RAID 0 + RAID 1) -supports JBOD function -Supports concurrent dual ATA133 IDE controller operation -Supports IDE bus master operation -Displays status and error checking messages during boot-up -Mirroring supports automatic background rebuilds -Features LBA and Extended Interrupt 13 drive translation in controller onboard BIOS FDD Connections • 1 FDD connection, allows connection of 2 FDD devices (Note 1) To use a DDRII 600 memory module on the motherboard, you must install an 800MHz FSB processor and overclock in BIOS. (Note 2) Only support ATAPI mode for HDD. GA-8I915P Duo Motherboard - 10 Onboard SATA • 4 Serial ATA connections • Supported on the Win 2000/XP operating systems Peripherals • 1 parallel port supporting Normal/EPP/ECP mode • 2 Serial port (COMA/COMB) • 8 USB 2.0/1.1 ports (rear x 4, front x 4 via cable) • 1 front audio connector • 1 IR connector • 1 PS/2 keyboard port • 1 PS/2 mouse port Onboard LAN • Onboard Marvell 8001 chip (10/100/1000 Mbit) • 1 RJ 45 port Onboard Audio • ALC850 CODEC (UAJ) • Supports Jack Sensing function • Supports 2 / 4 / 6 / 8 channel audio • Supports Line In ; Line Out (Front Speaker Out) ; MIC ; Surround Speaker Out (Rear Speaker Out) ; Center/Subwoofer Speaker Out ; Side Speaker Out connection • Supports SPDIF In/Out connection • CD In I/O Control • IT8712 Hardware Monitor • System voltage detection • CPU temperature detection • CPU / System fan speed detection • CPU warning temperature • CPU / System fan failure warning • CPU smart fan control BIOS • Use of licensed AWARD BIOS • Supports Q-Flash Additional Features • Supports @BIOS • Supports EasyTune 5 Overclocking • Over Voltage via BIOS (CPU/DDR/PCIE/FSB) • Over Clock via BIOS (CPU/DDR/PCIE) Form Factor • ATX form factor; 30.5cm x 22.0cm English -11 - Hardware Installation English Fig. 3 Fig. 4 Notice the small gold Once the CPU is colored triangle located properly inserted, on the edge of the CPU please replace the socket. Align the load plate and indented corner of the push the metal lever back into its original CPU with the triangle and gently insert the CPU into position. position. (Grasping the CPU firmly between your thumb and forefinger, carefully place it into the socket in a straight and downwards motion. Avoid twisting or bending motions that might cause damage to the CPU during installation.) 1-3 Installation of the CPU and Heatsink Before installing the CPU, please comply with the following conditions: 1. Please make sure that the motherboard supports the CPU. 2. Please take note of the one indented corner of the CPU. If you install the CPU in the wrong direction, the CPU will not insert properly. If this occurs, please change the insert direction of the CPU. 3. Please add an even layer of heat sink paste between the CPU and heatsink. 4. Please make sure the heatsink is installed on the CPU prior to system use, otherwise overheating and permanent damage of the CPU may occur. 5. Please set the CPU host frequency in accordance with the processor specifications. It is not recommended that the system bus frequency be set beyond hardware specifications since it does not meet the required standards for the peripherals. If you wish to set the frequency beyond the proper specifications, please do so according to your hardware specifications including the CPU, graphics card, memory, hard drive, etc...