Stimmen - 0, Durchschnittliche Bewertung: 0
(
)
)
|
Anleitung Zusammenfassung
Align the CPU pin one marking (triangle) with the pin one corner of the CPU socket (or you may align the CPU notches with the socket alignment keys) and gently insert the CPU into position. Step 5: Once the CPU is properly inserted, replace the load plate and push the CPU socket lever back into its locked position. GA-P35-DQ6 Motherboard - 14 ■ 1-3-2 Installing the CPU Cooler Follow the steps below to correctly install the CPU cooler on the motherboard. (The following procedure uses Intel® boxed cooler as the example cooler.) Step 1: Apply an even and thin layer of thermal grease on the surface of the installed CPU. Step 3: Place the cooler atop the CPU, aligning the four push pins through the pin holes on the motherboard. Push down on the push pins diagonally. Male Push Pin The Top of Female Push Pin Female Push Pin Step 2: Before installing the cooler, note the direction of the arrow sign on the male push pin. (Turning the push pin along the direction of arrow is to remove the cooler, on the contrary, is to install.' Step 4: You should hear a "click" when pushing down each push pin. Check that the Male and Female push pins are joined closely. (Refer to your CPU cooler installation manual for instructions on installing the cooler.) Step 5: After the installation, check the back of the motherboard. If the push pin is inserted as the picture above, the installation is complete. Use extreme care when removing the CPU cooler because the thermal grease/tape between the CPU cooler and CPU may adhere to the CPU. Inadequately removing the CPU cooler may damage the CPU. Step 6: Finally, attach the power connector of the CPU cooler to the CPU fan header (CPU_FAN) on the motherboard. rr\ r\ NOTE' - 15 - Hardware Installation English English 1-3-3 Removing the Crazy Cool Heatsink from the Back of the Motherboard To install a non-Intel CPU cooler that requires extra mounting holes, follow the steps below to remove the Crazy Cool heatsink from the back of the motherboard. Tools needed: 1. A Philip's screwdriver 2. A long nose plier 3. Screw nuts included with the motherboard The Crazy Cool Heatsink Step 1: Use a Philip's screwdriver to unfasten the three screws as shown in the picture to the left and remove the screws. Step 2: Unfasten the two spring screws around the heatsink on the North Bridge (as shown in the picture to the left). Do not remove the spring screws. Step 4: After removing/unfastening the screws, you may easily remove the Crazy Cool heatsink. Step 3: Before unfastening the spring screw as circled in the picture to the left, first remove the copper fin marked with "SI -LENT-PIPE." Step 5: ¡¡P'S? ^,'W ;• SB Step 6: Push down on one of ¡¡fe'i . ;«®j Do the same for the the two spring screws other spring screw and put the nut on the bottom of the spring screw on the back of the motherboard by a couple of turns. Do not fasten It to the full. Step 7: Finally, you can fully tighten the nuts and complete the steps to remove the Crazy Cool heatsink. (Remember to replace the copper fin.) Refer to your CPU cooler installation manual for instructions on installing the cooler. (Note) The components received may vary in appearance from the products illustrated. GA-P35-DQ6 Motherboard - 16 - 1-4 Installing the Memory A Read the following guidelines before you begin to install the memory: • Make sure that the motherboard supports the memory. It is recommended that memory of caution the same capacity, brand, speed, and chips be used. (Go to GIGABYTE's website for the latest memory support list.) • Always turn off the computer and unplug the power cord from the power outlet before installing the memory to prevent hardware damage. • Memory modules have a foolproof design. A memory module can be installed in only one direction. If you are unable to insert the memory, switch the direction. 1-4-1 Dual Channel Memory Configuration This motherboard provides four DDR2 memory sockets and supports Dual Channel Technology. After the memory is installed, the BIOS will automatically detect the specifications and capacity of the memory. Enabling Dual Channel memory mode will double the original memory bandwidth. The four DDR2 memory sockets are divided into two channels and each channel has two memory sockets as following: » Channel 0: DDRII1, DDRII2 » Channel 1: DDRII3, DDRII4 ►► Dual Channel Memory Configurations Table DDRII1 DDRII2 DDRII3 DDRII4 Two Modules DS/SS DS/SS DS/SS DS/SS Four Modules DS/SS DS/SS DS/SS DS/SS (SS=Single-Sided, DS=Double-Sided, "- -'-No Memory) crcr crcr DD DD DD DD Due to chipset limitation, read the following guidelines before installing the memory in Dual Channel mode. 1. Dual Channel mode cannot be enabled if only one DDR2 memory module is installed. 2. When enabling Dual Channel mode with two or four memory modules, it is recommended that memory of the same capacity, brand, speed, and chips be used and installed in the same co...