A list of the Factory Service Center locations and phone numbers is provided on page 24 for your convenience. 21 LIMITED WARRANTY - California Only - Makita U.S.A., Inc. a distributor of utility and ¡awn and garden equipment in the U.S., warrants to the owner of 1995 and later utility and/or lawn and garden equipment engines that the engine 0) has been designed, built, and equipped at the time of manufacture so as to conform with the applicable regulations of the California Air Resources Boa

Don't force small tool or attachment to do the job of a heavy-duty tool. Don't use tool for purpose not intended. 7. DRESS PROPERLY. Don't wear loose clothing or jewelry. They can be caught in moving parts. Rubber gloves and non-skid footwear are recommended when working outdoors. Wear protective hair covering to contain long hair. 8. USE SAFETY GLASSES. Also use face or dust mask if cutting operation is dusty. caoutchouc et les chaussures anti-dérapantes sont conseillés si vous travaillez de

Insert the battery cartridge so that the plus and minus terminals on the battery cartridge are on the same sides as their respective markings on the fast charger. insert cartridge fully into the port so that it rests on the charger port floor. Fig. 1 CAUTION : .Your new battery cartridge is not charged. You will need to charge it before use. 0 If you try to charge a cartridge from a just-operated tool, sometimes the charging light will not come on after you insert a cartridge from a just operate

That extension cord is properly wired and ingood electrical condition; and c. That wire size is at least as large as the one specified in the table below. TABLE 1 RECOMMENDED MINIMUM AWG SIZE FOR EXTENSION CORDS FOR BATTERY CHARGERS -~ Length of Cord (Feet) 25 50 100 150 AWG Size of Cord 18 18 18 16 ADDITIONAL SAFETY RULES FOR BATTERY 1. Always charge the Makita battery 122 immediately after purchase. 2. Always recharge the Makita battery 122 after use. 3. Be sure to charge the Makita battery 12

Shipping Weight 8.2 lbs. UPC Code 088381-07819-1 All specifications subject to change without prior notice. All models and accessories subject to stock on hand. 2CLF-0906 3K MA-0950-06 For more information, call 1-800-4MAKITAor visit makitatools.comMakita U.S.A., 14930 Northam St., La Mirada, CA 90638 Model JS8000 FIBER CEMENT SHEAR Makita offers a wide variety of accessories for Shears. For a complete listing, please refer to the Makita General Catalog, or visit our website at makitatools.com,

WARN IN G Read the important safety instructions For your personal safety, READ and UNDERSTAND before using Use only the Makita battery 121 or 122. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. IMPORTANT SAFETY INSTRUCTIONS __ 1 1 Name Plate 2 1 Screw M5x33 3 6 Tapping Screw 8T M4x16 4 1 Handle Set W t h Item 81 5 1 Inlet 6 1 Compression Spring 3 1 1 Lock.Off Button 8 1 Handle Set W t h Item 41 9 1 Makita Label 1 0 1 Square Nu1 M 5 11 1 Side Handle 1 2 1 Switch Lever 1 3 1 Switch 1 4 1 P P R i n

5. Do not put the tool on the chips of the workpiece. Otherwise it can cause damage and trouble on the tool. 6. Do not leave the tool running. Operate the tool only when hand-held. 7. Always be sure you have a firm footing. Be sure no one is below when using the tool in high locations. 8. Do not touch the blade or the workpiece immediately after operation; they may be extremely hot and could burn your skin. 9. Avoid cutting electrical wires. Itcan cause serious accident by electric shock. SAVE T

Clean inside blade cover of any built- up dirt. Loose Blade Follow steps 1 and 2 of Blade Replacement and tighten nut clockwise. Lubrication of Gears There is usually sufficient grease to last at least 4 years or 100 hours of domestic use before topping it up. The grease in the gear case should be filled up according to use by adding light, free-flowing grease (available from Mantis, P/N #9985) through screw hole marked “fill” (Picture 4). Use a suitable filling gun or squeeze grease pack. Remov

Division of Schiller-Pfeiffer, Inc. 1028 Street Rd. Southampton, PA 18966 800024 LITTLE WONDER' EXTENDED The Extended Reach Hedge Trimmer works great for hard to reach hedges, cutting at different angles and makes quick work of ground cover. With fast blade adjustments and ease of use, the Extended Reach Hedge Trimmer is a time and money saving tool for landscapers. Chrome vandium blades for precise cutting. Stays sharper, longer than conventional metal blades. ' \a ... M3- Adjust blade

Designed for added user comfort - Shock mounts in handles reduce vibration, and the precision balanced design make these units easier to use over extended periods. Throttle features - Finger throttle control and lock out lever give the user enhanced engine and blade control to prevent inadvertent blade engagement. Safety comb - Holds thick growth longer for superior cutting performance, and reduces the risk of injury. rocating blades Superior blade design 2124 24 . 12.2 2130 30 . 12.9 4100 CUTS