Stimmen - 4, Durchschnittliche Bewertung: 5
(
)
)
|
Anleitung Zusammenfassung
. . . . . . . . . . . . . . . .791-153066 Fuel Cap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .791-181612 Shoulder Harness . . . . . . . . . . . . . . . . . . . . . . . .791-682075B Tip-and-Pour 2-Cycle Oil (16 oz.) . . . . . . . . . . . . . .791-180965 These replacement parts can be purchased at the retailer from which you bought your trimmer, or your local Cub Cadet dealer. CLEANING To avoid serious personal injury, always turn your trimmer off and allow it to cool before you clean or do any maintenance on it. Use a small brush to clean off the outside of the unit. Do not use strong detergents. Household cleaners that contain aromatic oils such as pine and lemon, and such as kerosene, can damage plastic housing or handle. Wipe off any moisture with a soft cloth. STORAGE • Never store the unit with gasoline in the tank where fumes may reach an open flame or spark. • Allow the engine to cool before storing. • Store the unit locked up to prevent unauthorized use or damage. • Store the unit in a dry, well ventilated area. • Store the unit out of the reach of children. LONG TERM STORAGE If the unit will be stored for an extended time, 1. Drain all fuel from the gas tank into a container. Do not use fuel that has been stored for more than 60 days. Dispose of the old fuel in accordance to Federal, State, and Local regulations. 2. Start the engine and allow it to run until it stalls. This ensures that all gasoline has been drained from the carburetor. 3. Allow the engine to cool. Remove the spark plug and put 1 oz. (30 ml) of high quality motor oil into the cylinder. Pull the starter rope slowly to distribute the oil. Reinstall the spark plug. NOTE: Remove the spark plug and drain all of the oil from the cylinder before attempting to start the trimmer after storage. 4. Thoroughly clean the unit and inspect for any loose or damaged parts. Repair or replace damaged parts and tighten loose screws, nuts or bolts. The unit is ready for storage. TRANSPORTING • Allow the engine to cool before transporting. • Secure the unit while transporting. • Drain the gas tank before transporting. • Tighten gas cap before transporting. Section 7 Troubleshooting ENGINE WILL NOT START CAUSE ACTION On/Off Stop Control is in STOP position Turn On/Off Stop Control to START Empty fuel tank Fill fuel tank with properly mixed fuel Primer bulb wasn't pressed enough Press primer bulb fully and slowly 5-7 times Engine flooded Use starting procedure with choke lever in the RUN position, Pg. 10 Old or improperly mixed fuel Drain gas tank / Add fresh fuel mixture Fouled spark plug Replace or clean the spark plug Plugged spark arrestor Clean or replace spark arrestor ENGINE WILL NOT IDLE CAUSE ACTION Air Filter is Plugged Replace or clean the air filter Old or improperly mixed fuel Drain gas tank / Add fresh fuel mixture Improper carburetor adjustment Adjust per instruction Pg. 16 ENGINE WILL NOT ACCELERATE CAUSE ACTION Old or improperly mixed fuel Drain gas tank / Add fresh fuel mixture Improper carburetor adjustment Take to an authorized service dealer for carburetor adjustment Cutting attachment bound with grass Stop the engine and clean the cutting attachment Dirty air filter Clean or replace the air filter Plugged spark arrestor Clean or replace spark arrestor ENGINE LACKS POWER OR STALLS WHEN CUTTING CAUSE ACTION Old or improperly mixed fuel Drain gas tank / Add fresh fuel mixture Improper carburetor adjustment Take to an authorized service dealer for carburetor adjustment Fouled spark plug Replace or clean the spark plug Plugged spark arrestor Clean or replace spark arrestor CUTTING ATTACHMENT WILL NOT ADVANCE LINE CAUSE ACTION Cutting attachment bound with grass Stop the engine and clean cutting attachment Cutting attachment out of line Refill with new line Inner reel bound up Replace the inner reel Cutting head dirty Clean inner reel and outer spool Line welded Disassemble, remove the welded section and rewind the line Line twisted when refilled Disassemble and rewind the line Not enough line is exposed Push the Bump Knob and pull out line until 4 inches (102 mm) of line is outside of the cutting attachment Section 8 Specifications ENGINE Engine Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . Air-Cooled,2-Cycle Displacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.4 cu.in.(25 cc) Clutch Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . Centrifugal Idle Speed RPM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2,400-3,600 rpm Operating RPM (Trimmer) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....