Stimmen - 2, Durchschnittliche Bewertung: 4.5
(
)
)
|
Anleitung Zusammenfassung
2. Press and hold the release button (Fig.12). 3. While firmly holding the upper shaft housing, pull the cutting attachment or add-on straight out of the coupler (Fig.12). Coupler Release Button Fig. 12 WARNING: To avoid serious injury and damage to the unit, shut off the unit before removing or installing attachments. STARTING INSTRUCTIONS 1. Check the oil level in the crankcase. Refer to Checking the Oil Level ( p.] 2). 2. Turn switch to ON position (Fig.] 4). NOTE: If your unit is equipped with a spring loaded type ON/OFF switch, it will always remain in the ON position. 3. Place trimmer firmly on the ground or a very sturdy work surface. Make sure cutting head is clear of all objects. Make sure all bystanders are a minimum of 50 feet (15m) away. Do not attempt to start near pilot lights or any open flame. Do not smoke. Grasp the starter rope handle with one hand and the handle pole with the other hand ( Fig.] 3). Fig. 13 4. With the unit in the starting position, do not squeeze the throttle control (Fig.] 4). Then pull the rope smoothly and briskly. The engine should start. A cold engine should start with 3-5 pulls. A warm engine should start on the first pull. NOTE: On the very first use, it may take extra pulls to fill the fuel system with propane. 5. Squeeze the throttle control slightly to warm up the engine for 15 to 30 seconds. In cold weather, move the throttle slowly until the engine warms up for 30 to 60 seconds. NOTE: This unit is provided with a Fast Idle Lock (Fig. 14). If experiencing starting difficulties under regular conditions, squeeze the throttle control, then push and hold the Fast Idle lock forward while releasing the throttle trigger. Then start the unit. Start/On(I) Fast Idle Stop/Off Lock Safety trigger Throttle Control Fig. 14 NOTE: When starting the engine in very hot or cold conditions it may be necessary to squeeze the throttle control while pulling the starter rope. STOPPING INSTRUCTIONS 1. Release your hand from the throttle control. Allow the engine to cool down by idling. 2. If your unit is equipped with a spring loaded ON/ OFF switch, press and hold the button on OFF until the unit stops. Otherwise, push the switch to the off position. 3. When done using the trimmer for the day, disconnect the propane canister from the unit. WARNING: Avoid accidental starting. Make sure you are in the starting position when pulling the starter rope (Fig. 13). To avoid serious injury, the operator and unit must be in a stable position while starting. Make sure that any add-on item is installed correctly and secure before starting the unit. WARNING: Always wear eye, hearing, foot and body protection to reduce the risk of injury when operating this unit. 10 OPERATING YOUR TRIMMER Before operating the unit, stand in the operating position (Fig. 15). Check for the following: • The operator is wearing eye protection and proper clothing. • With a slightly bent right arm, the operator's right hand is holding the shaft grip. • The operator's left arm is straight, and left hand holding the upper handle. • The unit is at waist level. • The cutting attachment is parallel to the ground and easily contacts the grass without the need to bend over. HOLDING THE TRIMMER • Trim only when grass and weeds are dry. • The life of your cutting line is dependent upon: 1. Proper adherence to explained trimming techniques 2. What vegetation is cut 3. Where vegetation is cut For example, the line will wear faster when trimming against a foundation wall as opposed to trimming around a tree. Some line breakage will occur from: • Entanglement with foreign matter • Normal line fatigue • Attempting to cut thick, stalky weeds • Forcing the line into objects such as walls or fence posts NOTE: This unit is equipped with an Anti-Kickback bar. This bar helps protect you from "kick-back" which may occur during operation. The Anti-Kickback bar hits the side of your leg when the trimmer jumps back, preventing the cutting head to contact the operator. Fig. 15 TIPS FOR BESTTRIMMING RESULTS • For best trimming results, operate unit at full throttle. • Keep the cutting attachment parallel to the ground. Do not force the cutting attachment. Allow the tip of the line to do the cutting, especially along walls. Cutting with more than the tip will reduce cutting efficiency and may overload the engine. • Cut grass over 8 inches (200 mm) by cutting from top to bottom in small increments to avoid premature line wear or engine drag. Slowly move the trimmer into and out of the cutting area at the desired height. Move either in a forward- backward or side-to-side motion. Cutting shorter lengths produces the best results. 11 FREQUENCY MAINTENANCE REQUIRED REFER TO EVERY10HOURS CLEANAND RE-OILAIRFILTER PAGE 13 EVERY25HOURSTHEREAFTER CHECKOIL PAGE 13 L%/ERY25HOURS CHECKSPARKPLUGPOSIT1ONGAP PAGE 4 EVERY2SHOURS ROCKERARMCLEARANCEADJUSTMENT PAGE 16 CHECKING THE OIL LEVEL Perform these required maintenance procedures at the frequency stated in the t...
Dieses Handbuch ist für folgende Modelle:Haarschneidegeräte - 104.79212 (2.08 mb)