Stimmen - 3, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Replace or repair damaged cords. • WARNING: To prevent electrical shock hazard, use only with an extension cord suitable for outdoor use. Always connect extension cords to a fused line or one protected by a circuit breaker. To reduce the risk of electric shock, this equipment has a polarized plug (one blade is wider than the other) and will require the use of a polarized extension cord. The appliance plug will fit into a polarized extension cord only one way. If the plug does not fit fully into the extension cord, reverse the plug. If the plug still does not fit, obtain a correct polarized extension cord. A polarized extension cord will require the use of a polarized wall outlet. This plug will fit into the polarized wall outlet only one way. If the plug does not fit fully into the wall outlet, reverse the plug. If the plug still does not fit, contact a qualified electrician to install the proper wall outlet. Do not change the equipment plug, extension cord receptacle, or extension cord plug in any way. Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. The table shows the correct size to use depending on cord length and nameplate ampere rating. If in doubt, use the next heavier gauge. The smaller the gauge number, the heavier the cord. If the extension will be used outside, the cord must be suitable for outdoor work. The letters “WA” on the cord jacket indicate that the cord is suitable for outdoor use. SAFETY WARNINGS AND INSTRUCTIONS: POLARIZED PLUGS SAFETY WARNINGS AND INSTRUCTIONS: EXTENSION CORDS Minimum Gauge for Cord Sets Volts Total Length of Cord in Feet 120V 0-25 26-50 51-100 101-150 240V 0-50 51-100 101-200 201-300 Ampere Rating More Not more American Wire Gauge Than Than 0 - 6 18 16 16 14 6 - 10 18 16 14 12 10 - 12 16 16 14 12 12 - 16 14 12 Not Recommended SAVE THESE INSTRUCTIONS Figure 1 Figure 2 Raised Lug Borne Ceja Rotate 90. Faire pivoter sur 90. Gire 90. Figure 3 Figure 4 Figure 5 Cut-off Blade Lame de coupe Cuchilla de corte 10 - 30 0 0 Figure 6 Figure 7 Figure 8 Figure 9 Figure 10 Push Button Bouton-poussoir Oprima el boton Push Button Bouton-poussoir Oprima el boton Extend Tube Tube de rallonge Extienda el tubo Height Adjustment is available only on Model GH500 Dispositif de reglage de la hauteur, modele GH500 El ajuste de altura solo esta disponible en los modelos GH500 Figure 11 Figure 12 Cutting Line Fil tranchant Linea de Corte Figure 14 Figure 13 Figure 15 Conversion Button Bouton de conversion Boton de conversion Air Intake Slots Fentes d’admission d’air Tomas de aire • WARNING: The guard must always be on the tool to protect the user. NEVER OPERATE TOOL WITHOUT GUARD FIRMLY IN PLACE. Unplug the tool before attempting to attach the guard. 1. Attach edge guide to guard, as shown in Figure 1. 2. Press the guard against the motor housing, as shown in Figure 2 and rotate the guard 90 degrees clockwise until you hit a stop on the housing. 3. With the guard installed, insert the screw, (see figure 3) through the hole in the guard and into the bottom of the Trimmer housing. Tighten the screw. The screw will firmly retain the guard to your trimmer. 4. The guard is not intended to be removed. 5. Secure the extension cord with cord retainer as shown in Figures 4 and 5. 6. The auxiliary handle can be located all around the tube and all the way up and down. Simply loosen the knob and position the handle as desired. • CAUTION: ALWAYS WEAR EYE PROTECTION • CAUTION: Inspect area to be trimmed and remove any wire, cord, or string-like objects which could become entangled in the rotating line or spool. Be particularly careful to avoid any wire which might be bent outwardly into the path of the tool, such as barbs at the base of a chain link fence. ASSEMBLY / ADJUSTMENT SET-UP OPERATING INSTRUCTIONS 1. Angle unit as shown in Figure 6. 2. Slowly swing trimmer side to side, as shown in Figure 7. 3. To convert for maintenance edging (Figure 8) unplug from power source, depress conversion button and rotate the motor housing. 4. When the button snaps back into place the tool is locked in the edger position. 5. Return to trimming position by unplugging the tool, depressing the button and rotating back. 6. To operate as a maintenance edger, position tool above sidewalk, as shown in Figure 9. Rest edge guide as shown in Figure 9. 7. The GH500 is equipped for height adjustment, as shown in Figure 10. Cutting Line LINE FEEDING Your trimmer uses .065” (1.65 mm) diameter nylon line to cut grass and weeds quickly and easily. In time, the tip of the nylon line will become frayed and worn and the special self feeding line hub will automatically feed and trim a fresh length of line. Of course cutting line will wear faster and require more feeding if the cutting is done along sidewalks or other abrasive surfaces ...
Dieses Handbuch ist für folgende Modelle:Haarschneidegeräte - GH500 (306.68 kb)