Stimmen - 3, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
B) Unless the tool is fitted with a mains cable, you will need to connect an extension cable to the power inlet. . Connect the female socket of a suitable extension cable to the power inlet of the tool. . Loop the cable through the cable restraint (7) as shown to prevent the extension cable from becoming detached during use. . Insert the mains plug into a mains outlet. Warning! The extension cable must be suitable for outdoor use. When using a cable reel, always unwind the cable completely. Use Warning! Let the tool work at its own pace. Do not overload. . Carefully guide the cable in order to avoid accidentally cutting it. A good way to control the cable is by putting it over your shoulder. 4 ENGLISH For your safety, this tool is equipped with a double switching system. This system prevents starting the tool inadvertently and will only allow operation while holding the tool with both hands. Switching on and off Switching on Take hold of the front handle (3) with one hand so that the front handle switch (2) is pushed into the body of the tool. With the other hand, squeeze the trigger switch (1) to start the tool. Switching off Release the handle switch (2) or the trigger switch (1). Warning! Never attempt to lock a switch in the on position. Hints for optimum use Start by trimming the top of the hedge. Slightly tilt the tool (up to 15° relative to the line of cut) so that the blade tips point slightly towards the hedge (fig. C1). This will cause the blades to cut more effectively. Hold the tool at the desired angle and move it steadily along the line of cut. The double-sided blade allows you to cut in either direction. In order to obtain a very straight cut, stretch a piece of string along the length of the hedge at the desired height. Use the string as a guideline, cutting just above it. In order to obtain flat sides, cut upwards with the growth. Younger stems move outwards when the blade cuts downwards, causing shallow patches in the hedge (fig. C2). Take care to avoid any foreign objects. Especially avoid hard objects such as metal wire and railings, as these could damage the blades. Regularly oil the blades. Maintenance Your tool has been designed to operate over a long period of time with a minimum of maintenance. Continuous satisfactory operation depends upon proper tool care and regular cleaning. Warning! Before performing any maintenance, switch off and unplug the tool. After use, carefully clean the blades. After cleaning, apply a film of light machine oil to prevent the blades from rusting. Regularly clean the ventilation slots in your tool using a soft brush or dry cloth. Regularly clean the motor housing using a damp cloth. Do not use any abrasive or solvent-based cleaner. Make sure all switches are free of debris before and after use. Removing the guard (fig. A) Warning! Remove the guard for servicing purposes only. Always re-fit the guard after finishing servicing. Insert small pins into the holes (9) at either side of the bracket (8) and pull the guard (4) forward. Remove the pins and take the guard off the tool. Troubleshooting If the tool does not operate correctly, check the following. Fault Possible cause Action Tool will not start. Blown fuse. Replace fuse. Tripped RCD. Check RCD. Mains lead not connected. Check mains supply. Protecting the environment Separate collection. This product must not be disposed of with normal household waste. Should you find one day that your Black & Decker product needs replacement, or if it is of no further use to you, do not dispose of it with household waste. Make this product available for separate collection. Separate collection of used products and packaging allows materials to be recycled and used again. Re-use of recycled materials helps prevent environmental pollution and reduces the demand for raw materials. 5 ENGLISH Local regulations may provide for separate collection of electrical products from the household, at municipal waste sites or by the retailer when you purchase a new product. Black & Decker provides a facility for the collection and recycling of Black & Decker products once they have reached the end of their working life. To take advantage of this service please return your product to any authorised repair agent who will collect them on our behalf. You can check the location of your nearest authorised repair agent by contacting your local Black & Decker office at the address indicated in this manual. Alternatively, a list of authorised Black & Decker repair agents and full details of our after-sales service and contacts are available on the Internet. Technical data HT420 HT500 Voltage VAC 120-220 120-220 Power input W 400 420 Blade strokes (no load) min-1 1,900 1,900 Blade length cm 42 50 Blade gap mm 16 16 Blade brake time s < 1.0 < 1.0 Weight (excl. supply cord) kg 2.2 2.3 6 ESPANOL Finalidad Su recortasetos Black & Decker ha sido disenado para cortar setos, arbustos y zarzas. Esta herramienta esta pensada unicamente para uso domesti...