Stimmen - 0, Durchschnittliche Bewertung: 0 ( )

Hersteller: Philips Dateigröße: 509.74 kb Dateiname: Unterrichtssprache:

. The appliance is equipped with an automatic voltage selector and is suitable for mains voltages ranging from 100 to 240 volts. . Only use the appliance in combination with the mains cord supplied. . If the mains cord is damaged, always have it replaced by one of the original type in order to avoid a hazard. . Make sure the appliance and the cord do not get wet. . Keep the appliance out of the reach of children. . Use, charge and store the appliance at a temperature between 15cC and 35cC. . This appliance is only designed for trimming the human beard. Do not use the appliance for any other purpose. . Do not use the appliance if the cutting unit is damaged or broken, as this may cause injury. . Charge the appliance fully before using it for the first time (see chapter 'Charging'). . When the appliance has been charged for the first time, we advise you to use it until the battery is completely empty. C C CHARGE CHARGE ENGLISH Charging 1 Make sure the appliance is switched off. 2 3 Insert the appliance plug into the appliance. Put the mains plug in the wall socket. C . The charging light goes on to indicate that the appliance is charging. It will take approx. 1 hour to fully charge the battery. The charging light blinks to indicate that the battery has been fully charged. Do not charge the appliance for more than 24 hours. When it is fully charged, the appliance has a cordless trimming time of up to 40 minutes. Optimising the lifetime of the rechargeable battery -Do not recharge the appliance in between the trimming sessions. -Discharge the battery completely twice a year by letting the motor run until it stops. -Do not keep the appliance plugged into a wall socket all the time. 6 ENGLISH Using the appliance C 9 9 Always comb your beard or moustache with a fine comb before you start trimming. If you are trimming for the first time, be careful Do not move the trimmer too fast. Make smooth and gentle movements. Corded trimming . To use the trimmer connected to the mains: switch the trimmer off, connect it to the mains and wait a few seconds before switching it on. If the battery is completely empty, wait one minute before switching the appliance on, as the trimmer might not start working right away. Do not run the appliance from the mains when the battery is fully charged. Trimming with comb attachment 1 Turn the Precision Zoom Lock` to the desired hair length setting (see table). The setting will appear in the window below the Precision Zoom Lock`. ENGLISH Hair length setting table C Resulting hair lengthHair length setting 1 1.5mm 2 2.5mm 3 4.0mm 4 5.5mm 5 7.5mm 6 9.5mm 7 12.0mm 8 15.0mm 9 18.0mm B If you are trimming for the first time, start by using the maximum hair length setting (9). 2 3 Switch the appliance on. Place the trimmer on the skin and move the trimmer slowly over the skin against the direction of hair growth while pressing it lightly. Make sure the surface of the comb attachment always stays in contact with the skin. . If a lot of hair has accumulated in the comb attachment: 4 Remove the comb attachment by pulling it off the appliance. ENGLISH Never pull at the flexible top of the comb attachment. Always pull at the bottom part. 5 Blow or shake the hair out of the comb attachment. C The selected hair length setting will not change when you do this. Trimming at the unique 'stubble look' setting C . Using the trimmer with the comb attachment set to setting 1 allows you to create a 'stubble look'. Trimming without comb attachment Use the trimmer without comb attachment to trim full beards and single hairs. C 1 Remove the comb attachment by pulling it off the appliance. Never pull at the flexible top of the comb attachment. Always pull at the bottom part. Switch the appliance on. C Make well-controlled movements. Touch the hair lightly with the trimmer. 2 3 ENGLISH Trimming with the precision trimmer C C C You can use the precision trimmer to shape your moustache and sideburns, to define contours and to cut single hairs. 1 2 Remove the comb attachment. Push the precision trimmer upwards. If the appliance is switched on, the precision trimmer will start to work right away. Note: the main cutting unit continues to work when you use the pop-up precision trimmer. 3 Hold the appliance in vertical position and make strokes. The pop-up precision trimmer is also suitable for outlining the edges of the beard on the throat and on the cheeks. 4 When you have finished using the pop-up precision trimmer, push it back into the appliance. You can now put the comb attachment back onto the appliance. Cleaning Do not use abrasives, scourers or liquids such as alcohol, petrol or acetone to clean the appliance. 1 Make sure the appliance is switched off and disconnected from the mains before you start cleaning it. 10 ENGLISH C C C C C Remove the comb attachment. Flip the cutting unit open. 4 Clean the cutting unit and the hair chamber with the brush supplied. 5 Close the cutting unit by pushing it back onto the applia...

Herunterladen

Geben Sie zwei Ziffern: