Stimmen - 0, Durchschnittliche Bewertung: 0
(
)
)
|
Anleitung Zusammenfassung
Before You Begin Preparing your beard for shaping Follow these steps to prepare your beard. Use a Norelco beard and moustache trimmer to trim your beard (Fig.3). Use a Norelco razor to shave larger areas of the skin (Fig.4). Shaping Now you can shape and define your facial hair style. Use the D-Finer Precise Shaper on a clean, dry face. Do not use any type of lotion or cream before using. Use the Precise Shaper only for its intended household use as described in this manual. Slide the specialty Hi- Definition Trimmer out until you hear a “click” and the Hi-Definition Trimmer snaps into position.You will see the slide-out mark (Fig. 5). The slide-out mark is hidden underneath the specialty Hi-Definition Trimmer and only becomes visible when the specialty Hi- Definition Trimmer has been slid out correctly and “clicks” into position. Switch the D-Finer Precise Shaper ON. Shape the contours of your beard and sideburns with the specialty Hi-Definition Trimmer. To contour most effectively, place the flat surface of the specialty Hi- Definition Trimmer in contact with the skin and move it against the direction of hair growth (Fig. 6). Make well-controlled movements. Touch the hair lightly with the specialty Hi- Definition Trimmer. NOTE: Since all hairs do not grow in the same direction, you may want to try different contouring positions (i.e., upwards, downwards, or across). Practice is best for optimum results. For additional styles and defining tips, visit our website: When you have created your desired beard contour, slide the specialty Hi-Definition Trimmer back down to its original position. Finishing Finally, use the narrow shaving mini-foil to shave along the contour edges to remove any stubble while creating a smooth clean beard line (Fig. 7). Before using mini-foil, always check mini-foil for wear or damage. If mini-foil shows signs of wear or damage, do not use shaver as injury may occur. Do not use until mini-foil has been replaced. 1 5 4 3 2 1 2 1 Gently press the shaving mini-foil to the skin. Do not press too hard. To maintain a shape, use the shaving mini-foil to shave along the edges to provide a smooth and clean beard line. Switch the D-Finer Shaper OFF. Put on the protective shaving head cap to protect the specialty Hi-Definition Trimmer and the shaving mini-foil. CLEANING . Always switch D-Finer Precise Shaper off before cleaning. . Do not use abrasives, scourers or liquids such as alcohol, benzene, bleach or acetone to clean the D-Finer Shaper. . Never clean the specialty Hi-Definition Trimmer or shaving mini-foil with the motor ON. . Do not apply pressure to specialty Hi- Definition Trimmer or shaving mini-foil. Do not touch specialty Hi-Definition Trimmer or shaving mini-foil with hard objects as this may damage them. . Do not use while bathing, showering or immerse the D-Finer in water or other liquids as damage to D-Finer Shaper may occur. . Clean cut hairs from D-Finer Shaper as they accumulate during use. . Always clean D-Finer Shaper after each use and before storing. Make sure D-Finer Shaper is switched OFF and disconnected from the electrical outlet. Make sure the specialty Hi-Definition Trimmer is down in its original position. Remove the removable shaving head by pulling it off the D-Finer body (Fig. 8). Shake or blow cut hairs from the shaving head. Carefully clean the cutting unit and the shaving head and body of the D-Finer Shaper with the brush supplied. Important: Do not clean the shaving minifoil with the brush. The brush may damage the shaving mini-foil. Put on the protective shaving head cap to protect the specialty Hi- Definition Trimmer and the shaving mini-foil (Fig. 9). Replacing The Shaving Mini-foil If the shaving mini-foil is worn or damaged, do not continue using the appliance. Replace the shaving mini-foil immediately. A worn or damaged shaving mini-foil should only be replaced with an original Philips shaving mini-foil, which is available at an authorized Norelco Service Location. Remove the detachable shaving head by pulling it from the appliance (fig. 10). Remove the shaving minifoil by pushing it out of the shaving head (fig. 11). Place the new shaving minifoil carefully in the shaving head (fig. 12). When the shaving mini-foil is properly positioned, push it into its end position with your finger (fig. 13). Replacing The Mini-foil Cutter The mini-foil cutter is located under the detachable shaving head. Do not switch the appliance on when replacing the mini-foil cutter. 4 3 2 1 5 4 3 2 1 2 3 4 5 6 7 8 9 2 1 If the mini-foil cutter is worn or damaged, do not continue using the appliance. Replace the mini-foil cutter and the shaving mini-foil immediately. A worn or damaged mini-foil cutter should only be replaced with an original Philips cutter, which is available at an authorized Norelco Service Location. Remove the detachable shaving head by pulling it from the Shaper (fig. 14) Remove the old mini-foil cutter by pulling it from the appli...