Stimmen - 0, Durchschnittliche Bewertung: 0
(
)
)
|
Anleitung Zusammenfassung
Continue using it until the battery is completely empty. w Do not charge for more than 24 hours. w Do not keep cord permanently plugged in. w Discharge/run down the battery completely twice a year by letting the motor run until it stops. w If the Trimmer hasn’t been used for a long period of time, it must be recharged for a full 10 hours. Cordless Trimming 1 Charge according to directions. Unplug Trimmer from outlet and remove cord. 2 Slide ON/OFF switch ON to begin trimming. 3 When finished, turn Trimmer OFF. Trimming w Use this Trimmer for its intended household use as described in this manual. w Always comb the beard and/or moustache with a fine comb before you start trimming. w If you are trimming for the first time, be careful. Do not move the Trimmer too fast. Make smooth and gentle movements. w Make sure that the Trimmer is fully charged before you start trimming. Trimming with the Beard Trimming Comb w Beard Trimming Comb must be on Trimmer to use the Zoom Lock. 1 Turn the Zoom Lock to the desired trimming length setting (see table). The setting is indicated in the center of the adjustment ring (fig. 3). w If you are trimming for the first time, start by using the comb at the maximum trimming length setting (#10) to prevent accidentally trimming hairs too short. As you become familiar with the settings, adjust Zoom Lock to desired trimming length. Zoom Lock will “click” into position at each setting. 2 Switch the Trimmer ON. 3 To trim in the most effective way, move the Trimmer against the direction of hair growth. Make sure the surface of the comb always stays in contact with the skin (fig. 4). NOTE: Since all hairs do not grow in the same direction, you may want to try different trimming positions (i.e., upwards, downwards, or across). Practice is best for optimum results. 4 If cut hairs have accumulated in the comb, turn Trimmer off, remove the comb and blow and/or shake the hair out of the comb (fig. 5). The selected trimming length setting will not change when you do this. Trimming For 'Stubble' Look 1 Be certain Beard Trimming Comb is on Trimmer and use setting 1 (3/64in/1mm) to result in a 'stubble' look (fig. 6). Trimming Without the Beard Trimming Comb Remove comb if you are: w Defining hair lines w Trimming nape of neck w Removing single, unwanted hairs 1 Be certain the Trimmer is in the OFF position. 2 Remove the Beard Trimming Comb by pulling it off the Trimmer (fig. 7). 3 Switch the Trimmer ON. 1 Unplug electrical cord from outlet and Trimmer before dismantling Trimmer. 2 Allow the Trimmer to run until the battery is completely empty/depleted. Turn Trimmer off. 3 Remove the comb and cutting unit from Trimmer. 4 Insert a screwdriver in the hair chamber to separate the housing part (fig. 15). 5 Cut the wires close to the battery with scissors (fig. 16). 6 Remove the rechargeable battery. 7 Do not attempt to replace battery. Insulate battery ends by covering with tape and or place battery in a small plastic bag. 8 Discard your Trimmer. Do not attempt to plug electrical cord into outlet or recharge the Trimmer after the battery has been removed. 9 Contact your local town or city officials for battery disposal information or call 1-800-8-BATTERY or for battery drop-off locations. 4 Make well-controlled movements. Touch the hair/skin lightly with the Trimmer (fig. 8). Be careful when you are trimming without the comb as when the Trimmer is turned on it will trim every hair it touches. Cleaning w Clean the Trimmer after each use. w Always switch Trimmer OFF, unplug and remove power supply cord from Trimmer before cleaning. w Never immerse the Trimmer in water or rinse under the tap (fig. 9). w Do not use abrasive cleaning agents, scourers or aggressive liquids such as alcohol, gasoline, or acetone to clean the Trimmer and attachments. w Never clean, replace or remove Trimmer comb with motor ON. w Do not apply pressure to cutters. w Do not touch cutters with hard objects as this may damage them. w Use a soft, dry cloth to clean Trimmer handle. During Use: w If cut hairs have accumulated in the comb area, turn Trimmer off, pull the comb off Trimmer and remove hairs by shaking, blowing or using cleaning brush provided. After Each Use: 1 Make sure the Trimmer is switched OFF and disconnected from the electrical outlet. 2 Remove the Trimming Comb and clean with the brush. 3 Remove the cutting unit by pushing against the teeth of the cutting unit (fig. 10) and rinse under warm tap water (fig. 11) or use the brush supplied. Allow to air dry thoroughly. 4 Place the cutting unit back by inserting the notch of the cutting unit into the guiding slot (fig. 12). 5 Push the cutting unit back into place on the Trimmer until you hear a click (fig. 13). NOTE: The appliance does not need any lubrication (oil). Replacing The Cutting Unit If your cutters become damaged or worn, do not continue using the Trimmer. Replace cutters immediately. 1 Open the cutting unit. 2 Remove the old cutting unit by pu...