Stimmen - 0, Durchschnittliche Bewertung: 0
(
)
)
|
Anleitung Zusammenfassung
-- Children should be supervised to ensure that they do not play with the appliance. 4222.002.8225.1 QG3050 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Caution -Use, charge and store the appliance at a temperature between 15°C and 35°C. -Only use the adapter supplied to charge the appliance. -If the adapter is damaged, always have it replaced with one of the original type in order to avoid a hazard. -Do not use an attachment or comb if it is damaged or broken, as this may cause injur y. -This appliance is only intended for clipping human scalp hair, shaving the human beard line and trimming the human beard, moustache, sideburns, nose hair, ear hair and eyebrows. Do not use it for any other purpose. -If the appliance is subjected to a major change in temperature, pressure or humidity, let the appliance acclimatise for 30 minutes before you use it. -Do not place the beard trimming comb or the hair clipping comb on the precision attachment. Compliance with standards -This Philips appliance complies with all standards regarding electromagnetic fields (EMF). If handled properly and according to the instructions in this user manual, the appliance is safe to use based on scientific evidence available today. Charging Charge the appliance fully before you use it for the first time or after a long period of disuse. It takes approx. 10 hours to charge the batter y fully. A fully charged appliance has a cordless operating time of up to 35 minutes. When you charge the appliance for 3 hours, you can use it for 15 minutes. The appliance does not run from the mains. Make sure the appliance is switched off during charging. 1 Insert the appliance plug directly into the appliance (Fig. 2). The charging light on the adapter indicates , that the appliance is charging. (Fig. 3) Optimising the lifetime of the rechargeable battery -Do not leave the appliance connected to the mains for more than 24 hours. -Discharge the batter y completely twice a year by letting the motor run until it stops. Then fully recharge the batter y. Clipping scalp hair Preparing for clipping Only use the appliance on dry scalp hair. Do not use it on freshly washed scalp hair. 1 Make sure that the appliance is fully charged. It is not possible to run the appliance from the mains when the batter y is empty. 2 Make sure that the head of the person whose hair you intend to cut is at the same level as your chest. This ensures that all par ts of the head are clearly visible and within easy reach. 3 Comb the hair in the direction of growth with the barber’s comb. Clipping with hair clipping comb 1 2 Put the hair clipping comb on the trimming attachment and push it home (‘click’) (Fig. 4). Press the hair length selector and slide the comb to the desired setting (see table below). (Fig. 5) The selected setting appears in the window , to the left of the hair length selector. Note:When you clip for the first time, start at the highest setting (9) to familiarise yourself with the appliance. settings of hair clipping comb 1 2mm 2 4mm 3 6mm 4 8mm 5 10mm 6 12mm 7 14mm 8 16mm Setting Hair length after clipping 9 18mm 3 To clip in the most effective way, move the appliance slowly against the direction of hair growth. (Fig. 6) -Do not move the appliance too fast. Make smooth and gentle movements. -Make sure that the flat par t of the comb is always fully in contact with the scalp to obtain an even result (Fig. 7). -Make overlapping passes over the head to ensure that all hair that should be cut is cut. -Pass the appliance slowly over the crown from different directions to achieve an even result (Fig. 8). 4 Regularly remove the comb to blow and/or shake out hair that has accumulated. You have to adjust the clipping length again after you have removed the comb. Contouring without hair clipping comb Be careful when you clip without comb, because the appliance removes every hair it touches. To remove the comb, press the hair length selector (1) and slide the comb upwards (2). (Fig. 9) 1 2 Use the appliance without the hair clipping comb to contour edges. -To shape the contours round the ears, tilt the appliance in such a way that only one edge of the trimming attachment touches the hair ends (Fig. 10). -To contour the nape hairline, hold the appliance with the teeth of the trimming attachment pointing towards the skin. (Fig. 11) -To contour the sideburns, hold the appliance with the teeth of the trimming attachment pointing towards the skin (Fig. 12). Trimming Preparing for trimming 1 2 Make sure that the hair is dry and clean. Comb the hair in the direction of growth with the barber’s comb. Beard trimming with comb 1 2 Put the beard trimming comb on the trimming attachment and push it home(‘click). (Fig. 13) Press the hair length selector and slide it to the desired setting (see table below). (Fig. 14) The selected setting appears in the window , to the left of the hair length selector. Note:When you trim for the first time, start at th...