Stimmen - 0, Durchschnittliche Bewertung: 0
(
)
)
|
Anleitung Zusammenfassung
Be careful when you clip without comb because the cutting element removes every hair it touches. 1 Press the setting selector upwards and pull the comb off the handle. (Fig. 12) 2 Before you start to contour the hairline round the ears, comb the hair ends over the ears. 3 Tilt the appliance in such a way that only one edge of the cutting element touches the hair ends when you shape the contours round the ears (Fig. 13). Only cut the hair ends. The hairline should be close to the ear. 4 To contour the neckline and sideburns, turn the appliance and make downward strokes (Fig. 14). Move the appliance slowly and smoothly. Follow the natural hairline. Cutting shapes with micro trimmer You can use the micro trimmer to cut shapes in scalp hair. It cuts hair very close to the skin (0.6mm). Be careful when you use the micro timmer because it removes every hair it touches. 1 Put the micro trimmer on the handle (see section ‘Attaching/detaching attachments’ in chapter ‘Preparing for use’). 2 Make careful and controlled movements with the micro trimmer. -- To achieve a good cutting result, move the trimmer against the direction of hair growth. -- Always make sure the micro trimmer is fully in contact with the skin. Trimming Preparing for trimming Make sure that the appliance is fully charged before you start trimming. It is not possible to run the appliance from the mains. 1 Comb the hair to be trimmed (beard, moustache, sideburns, eyebrows) with a fine comb. 2 Put the cutting element on the handle (see section ‘Attaching/detaching attachments’ in chapter ‘Preparing for use’). Beard trimming with beard trimming comb 1 Slide the beard trimming comb into the guiding grooves on both sides of the handle (‘click’) (Fig. 15). 2 Press the setting selector upwards or downwards to set the desired setting (Fig. 16). ,, The setting indicator on the back of the appliance shows the selected setting. The table shows how long the hair will be after trimming at the different settings. When you trim for the first time, start at the highest setting (9) to familiarise yourself with the appliance. Settings of beard trimming comb Settings 1 2 3 4 5 6 7 8 9 Hair length after trimming(mm) 2 4 6 8 10 12 14 16 18 3 Switch on the appliance. 4 Move the appliance through the hair slowly (Fig. 17). -- To trim in the most effective way, move the appliance against the direction of hair growth. -- Since all hair does not grow in the same direction, you need to move the appliance in different directions (upward or across). -- Make sure that the flat part of the comb is always fully in contact with the skin to obtain an even result. 5 Regularly remove cut hair from the comb. If a lot of hair has accumulated in the comb, remove the comb from the appliance and blow and/or shake the hair out of it. Trimming at the ‘stubble look’ setting 1 To create a ‘stubble look’, trim with the beard trimming comb set to hair length setting 1. (Fig. 18) Beard trimming without beard trimming comb Use the beard trimmer without the beard trimming comb to contour your beard and to remove single hairs. Cutting without comb results in a very short stubble beard (0.6mm). 1 Press the setting selector upwards and pull the beard trimming comb off the handle (Fig. 19). 2 Make careful and controlled movements with the beard trimmer. Touch the hair lightly with the cutting element. Beard trimming with precision trimmer and precision comb Use the precision trimmer with the precision comb to trim smaller areas and to create designer beards. 1 Put the precision trimmer on the handle (see section ‘Attaching/detaching attachments’ in chapter ‘Preparing for use’). 2 Slide the precision comb into the guiding grooves on both sides of the handle (‘click’) (Fig. 20). 3 Press the setting selector upwards or downwards to set the desired setting. (Fig. 21) ,, The setting indicator on the back of the appliance shows the selected setting. The table shows how long the hair will be after trimming at the different settings. When you trim for the first time, start at the highest setting (4) to familiarise yourself with the appliance. Settings of precision comb Setting 1 2 3 4 Hair length after trimming (mm) 2 4 6 8 Beard trimming with precision trimmer but without precision comb Use the precision trimmer without the precision comb to shape your moustache and sideburns, to define contours and to remove single hairs. 1 Press the setting selector upwards and pull the precision comb off the handle (Fig. 22). 2 Hold the appliance upright and trim the desired areas (Fig. 23). Grooming facial hair (nose hair, ear hair and eyebrows) Trimming nose hair 1 Put the nose/ear hair trimmer on the handle (see section ‘Attaching/detaching attachments’ in chapter ‘Preparing for use’). 2 Make sure your nostrils are clean. 3 Switch on the appliance and insert the tip of the trimmer into one of your nostrils. (Fig. 24) Do not insert the tip more than 0.5cm into your nostril. 4 Slowly move the tip in and out while turning ...