Stimmen - 3, Durchschnittliche Bewertung: 3.3 ( )

Hersteller: Echo Dateigröße: 425.97 kb Dateiname: Unterrichtssprache:

Try to fill each day with jobs where operating the trimmer or other hand-held power equipment is not required. • If you experience discomfort, redness and swelling of the fingers followed by whitening and loss of feeling, consult your physician before further exposing yourself to cold and vibration. Repetitive Stress Injuries - It is believed that overusing the muscles and tendons of the fingers, hands, arms and shoulders may cause soreness, swelling, numbness, weakness and extreme pain in those areas. Certain repetitive hand activities may put you at a high risk for developing a Repetitive Stress Injury (RSI). An extreme RSI condition is Carpal Tunnel Syndrome (CTS), which could occur when your wrist swells and squeezes a vital nerve that runs through the area. Some believe that prolonged exposure to vibration may contribute to CTS. CTS can cause severe pain for months or even years. To reduce the risk of RSI/CTS, do the following: • Avoid using your wrist in a bent, extended or twisted position. Instead try to maintain a straight wrist position. Also, when grasping, use your whole hand, not just the thumb and index finger. • Take periodic breaks to minimize repetition and rest your hands. • Reduce the speed & force in which you do the repetitive movement. • Do exercises to strengthen the hand and arm muscles. • Immediately stop using all power equipment and consult a doctor if you feel tingling, numbness or pain in the fingers, hands, wrists or arms. The sooner RSI/CTS is diagnosed, the more likely permanent nerve and muscle damage can be prevented. R OPERATOR'S MANUAL 9 DESCRIPTION The ECHO product you purchased has been factory pre-assembled for your convenience. Due to packaging restrictions, shield installation and positioning of the front handle are necessary. After opening the carton, check for damage. Immediately notify your retailer or ECHO Dealer of damaged or missing parts. Use the contents list to check for missing parts. IMPORTANT ENGINE INFORMATION EMISSION CONTROL - ENGINE FAMILY : TEH021UB24RA DISPLACEMENT : 21.2cc The emission control system for this engine is EM (Engine THIS ENGINE MEETS U.S. EPA PHI AND 1995 1999 CALIFORNIA EMISSION REGULATIONS Modification). FOR ULGE ENGINES. REFER TO OWNER’S MANUAL FOR MAINTENANCE SPECIFICA- Emission Control Labellocated on Engine TIONS AND ADJUSTMENTS. (EXAMPLE ONLY, information on label varies by FAMILY). 1 2 13 19 1517 20 21 5 4 6 14 18 7 16 3 8 CONTENT LIST 9 10 ____ 1 -Trimmer Assembly ____ -Power Head 11 ____ -Drive Shaft Assembly ____ 1 -Plastic Bag (Co-Pack) ____ -Operator's Manual 12 ____ -Safety Manual ____ -Shield Assembly ____ -Hardware Bag ____ -1, 1/4-20 bolt ____ -1, 1/4-20 wing nut ____ -1, 1/4-20 flat washer ____ -Shoulder Strap, GT-2400 only ____ -Warranty Card & Limited Warranty 22 ____ -Safety Glasses ____ -Oil 2 Stroke . OPERATOR'S MANUAL - Included in plastic bag (co-pack). Read before operation and keep in a safe place for future reference, i.e., operation, maintenance, storage and specifications. 2. SAFETY MANUAL - Included in plastic bag (co-pack). Read before operation and keep in a safe place for future reference to learn proper, safe operating techniques. 3. POWER HEAD - Factory Assembled to the Driveshaft assembly. Includes the Engine, Clutch, Fuel System, Ignition System and Recoil Starter. 4. FRONT HANDLE - The Front (loop) handle is factory assembled to the Drive Shaft assembly but must be repositioned for proper cutting attitude and operator comfort. 5. DRIVESHAFT ASSEMBLY - Factory Assembled to the Power Head. Includes the Rear (right hand) Handle Assembly, Bearing Housing Assembly, Throttle Trigger, Front (loop, left hand) Handle Assembly, Flexible Drive Cable and Safety Decals. 6. NYLON CUTTER HEAD - Contains replaceable nylon trimming line that advances when the trimmer head is tapped against the ground while the head is turning at normal operating speed. 7. CUT-OFF KNIFE - Trims line to the correct length (5"). If trimmer is operated without a cut-off knife the line will become too long - more than (5") - the operating speed will slow, the engine overheat and performance will suffer. 8. DEBRIS SHIELD ASSEMBLY - Included in plastic bag (co-pack). MUST be installed on unit before use, see Assembly Instructions. Shield assembly includes the Cut-Off Knife and Safety Decal. Mounts on the Bearing Housing Assembly just above the cutting attachment. Helps protect the operator by deflecting debris produced during the trimming operation. 9. THROTTLE TRIGGER - Spring loaded to return to idle when released. During acceleration, press trigger gradually for best operating technique. 10. GRIP - Rear (right hand) handle. 11. STOP SWITCHGT- 2000 - "TOGGLE SWITCH" mounted on the engine. Move switch UP to RUN, DOWN to STOP. GT-2400 - "SLIDE SWITCH" mounted on top of the Throttle Trigger Housing. Move switch FORWARD to RUN, BACK to STOP. 12. SHOULDER HARNESS- Standard, GT-2400, optional, GT-2000. An adjustable strap that suspends the ...

Herunterladen

Geben Sie zwei Ziffern: