Stimmen - 3, Durchschnittliche Bewertung: 3.7 ( )

Hersteller: Echo Dateigröße: 1.24 mb Dateiname: Unterrichtssprache:

1. Move stop switch to stop position. 2. Disconnect spark plug wire from spark plug. 3. Brush loose debris from blade and coat both sides of blade with the 50-50 cleaning mixture. 4. Allow cleaning mixture to soften the remaining gummy residue then wipe it from the blade. 5. Apply clean oil to the entire length of the blade. Be certain the blade bolts are lubricated. 6. Wipe excess oil from the blade before putting the unit back in service. Gear Box Assembly Level 1. Parts required: POWER BLENDXTM 14 oz. or Lithium Based Grease. 1. Clean dirt from grease fitting (A). 2. Apply 1-2 pumps of grease into fitting. DO NOT force grease. Too much pressure will force grease past seals and cause damage. 3. Wipe excess grease from around grease fitting. A sharpenIng blades Level 2. Parts required: None WARNING Hedge Clipper blades are very sharp. Touching them may lead to severe personal injury. Avoid touching blades whenever possible, and always wear gloves to protect hands. blade adjusTmenTLevel 2. WARNING Hedge clipper blades are very sharp. Touching them may lead to severe personal injury. Use long hex wrenches and sockets withextensions when tightening blade screws and blade locknuts to keep hands at a safe distance from sharp blades. 1. Move stop switch to STOP position. 2. Disconnect spark plug wire. 3. Tighten blade screws (A) securely. 4. Hold blade screws (A) to prevent turning, and tighten locknuts (B). A B 1. Move stop switch to stop position. 2. Disconnect spark plug wire. 3. Remove blade guard. (See “Blade Guard Remove/Install instructions”) 4. Slide blades to allow file clearance using slots (B) on bottom of blade. Do not pry against cutting edges. 5. File each edge carefully. Follow the original shape of the blade. IMPORTANT If a power grinder is used DO NOT allow blade to over heat. 6. Install blade guard. (See “Blade Guard Remove/Install instructions”) 7. Lubricate blades (see “Lubrication instructions”). IMPORTANT Blades should only be removed and reinstalled by an Authorized ECHO Servicing Dealer, otherwise premature wear or internal gearcase damage may occur. A 6mm (.25 in.) Radius B 45. IMPORTANT Blades should only be removed and reinstalled by an Authorized ECHO Servicing Dealer, otherwise premature wear or internal damage may occur. NOTE Locking ability of Hedge Clipper blade lock nuts will diminisheach time they are removed. Replace if turning resistance is notfelt when installing locknuts. Level 2. WARNING Hedge clipper blades are very sharp. Touching them may lead to severe personal injury. Use long hex wrenches and sockets withextensions when tightening blade screws and blade locknuts to keep hands at a safe distance from sharp blades. 1. Move stop switch to STOP position. 2. Disconnect spark plug wire. 3. Tighten blade screws (A) securely. 4. Hold blade screws (A) to prevent turning, and tighten locknuts (B). A B 1. Move stop switch to stop position. 2. Disconnect spark plug wire. 3. Remove blade guard. (See “Blade Guard Remove/Install instructions”) 4. Slide blades to allow file clearance using slots (B) on bottom of blade. Do not pry against cutting edges. 5. File each edge carefully. Follow the original shape of the blade. IMPORTANT If a power grinder is used DO NOT allow blade to over heat. 6. Install blade guard. (See “Blade Guard Remove/Install instructions”) 7. Lubricate blades (see “Lubrication instructions”). IMPORTANT Blades should only be removed and reinstalled by an Authorized ECHO Servicing Dealer, otherwise premature wear or internal gearcase damage may occur. A 6mm (.25 in.) Radius B 45. IMPORTANT Blades should only be removed and reinstalled by an Authorized ECHO Servicing Dealer, otherwise premature wear or internal damage may occur. NOTE Locking ability of Hedge Clipper blade lock nuts will diminisheach time they are removed. Replace if turning resistance is notfelt when installing locknuts. TroubleshooTIng ENGINE PROBLEM TROUBLESHOOTING CHART Problem Check Status Cause Remedy neiEng -cranks starts hard/ t'doesn start at carburetorlFue No fuel at carburetor Fuel strainer clogged ne cloggedilFuel Carburetor Clean or replace Clean or replace See your Echo dealer Fuel at cyilnder nderilNo fuel at cy Carburetor See your Echo dealer Muffler wet with fuel Mixture too richlFue Open choke ean/replace air filterlC Adjust carburetor See your Echo dealer Spark at end ug wirelof p No spark Stop switch off cal problemiElectr Interlock switch tch to ONiTurn sw See your Echo dealer See your Echo dealer uglSpark at p No spark ncorrectiSpark gap th carboniCovered w Fouled with fuel veiPlug defect ust to .65mm (0.026 in.)jAd Clean or replace Clean or replace uglReplace p Engine runs, es oribut d does not accelerate ylproper terlr fiiA ter dirtylr fiiA Normal wear ean or replacelC terliflFue rtyiter dlfilFue duesinants/resiContam ni fuel Replace ventlFue Fuel vent plugged dues ininants/resiContam fuel ean or replacelC Spark Plug rty/worniPlug d wearlNorma ean and adjust or replacelC Carbur...

Herunterladen

Geben Sie zwei Ziffern: