Stimmen - 2, Durchschnittliche Bewertung: 3.5 ( )

Hersteller: Homelite Dateigröße: 1.08 mb Dateiname: Unterrichtssprache:

1 Liter 20 cc (20 ml) Fig. 8 OPERATION ...... ................ .... .. .... .. .. ......OPERATING THE TRIMMER OPERATION ADVANCING THE STRING ADVANCING STRING USING THE EZ LINE™ TAP ADVANCE SYSTEM String advance is controlled by tapping string head on grass while running engine at full throttle. 1. Run engine at full throttle. 2. Tap string head on ground to advance string. String advances each time the head is tapped. 3. Several taps may be required until string strikes the cut off blade. 4. Resume trimming. NOTE: If the string is worn too short you may not be able to advance the string by tapping it on the ground. If so, STOP THE ENGINE, and manually advance the string. ADVANCING THE STRING MANUALLY Push the spool retainer down while pulling on string(s) to manually advance the string. CUT OFF BLADE This trimmer is equipped with a cut-off blade on the grass deflector. For best cutting, advance string until it is trimmed to length by the cut-off blade. Advance string whenever you hear the engine running faster than normal, or when trimming efficiency diminishes. This will maintain best performance and keep string long enough to advance properly. CUTTING TIPS See Figure 9. ¦ Keep the trimmer tilted toward the area being cut; this is the best cutting area. ¦ The curved shaft trimmer cuts when passing the unit from right to left. The straight shaft trimmer cuts when passing the unit from left to right. This will avoid throwing debris at the operator. Avoid cutting in the dangerous area shown in Figure 9. ¦ Use the tip of string to do the cutting; do not force string head into uncut grass. ¦ Wire and picket fences cause extra string wear, even breakage. Stone and brick walls, curbs, and wood may wear string rapidly. ¦ Avoid trees and shrubs. Tree bark, wood moldings, siding, and fence posts can easily be damaged by the string. ................................................................DANGEROUS CUTTING AREA BEST CUTTING AREA BEST CUTTING AREA DANGEROUS CUTTING AREA EASY REACH DIRECTION OF ROTATION TRIMLITE AND TRIM ‘N EDGE Fig. 9 ............................................................................................................................................................................................................................................................DIRECTION OF ROTATION Page 13 Page 14 .... EDGER GUIDE OPERATION - TRIM ‘N EDGE ONLY See Figures 10 and 11. ¦ Loosen the wing nut and slide the edger guide to adjust it to the desired trimming length then retighten the wing nut securely. Refer to “Edger Guide Assembly” earlier in this manual for additional information. ¦ The edger guide allows the trimmer to be used as an edger for cutting along sidewalks, driveways, flower beds, etc. The edger guide is convenient to use and supports the trimmer as it is being used as an edger. ¦ Be extremely careful when tilting the trimmer to use as an edger. The muffler, and the exhaust from the muffler get very hot during operation. Keep the muffler away from all body parts. See Figure 11. OPERATION Fig. 10 WING NUT EDGER GUIDE Fig. 11 Page 15 STSTOPOP A B C Fig. 12 THROTTLE TRIGGER PRIMER BULB OPERATION STARTING INSTRUCTION LABEL STOP A B C STARTING AND STOPPING See Figures 12 and 13. Trimmer should be on a flat, bare surface for starting. 1. Slowly press the primer bulb seven (7) times. 2. Set the choke lever to the FULL CHOKE position (A). 3. Squeeze the throttle trigger fully and pull starter handle sharply until engine attempts to run. Do not pull the starter handle more than eight (8) times. NOTE: Keep throttle trigger squeezed fully through STEP 6. 4. Set the choke lever to the HALF CHOKE position (B). 5. Pull the starter handle until the engine runs. Do not pull the starter handle more than six (6) times. 6. Allow the engine to run for 15 seconds, then set the choke lever...

Herunterladen

Geben Sie zwei Ziffern: