Stimmen - 1, Durchschnittliche Bewertung: 4 ( )

Hersteller: Electrolux Dateigröße: 1 mb Dateiname: Unterrichtssprache:

ENGLISH - 7 I. Techniques for use 1 4 5 6 7 8 9 10 11 12 13 14 16 Cutting techniques Tap gently on the ground with the button (A) as shown in the figure and the string will come out automatically. Accelerate again. If the string does not come out make sure there is still some left and try again. I2. Drawing out the string (B) In order to extend the nylon line as it wears down, pull the mower gauge downwards and turn it in a clockwise direction to feed out the desired length of line. I3. Thinning grass with the grass cutter blade The grass is cut with swinging motions from side to side, maintaining the blade parallel to the ound. During the right to left swing the grass is cut, while the backswing must be made without using the blade. KICKBACK can occur when cutting is done with the risk sector of the blade; we recommend cut- ting with the rest of the blade. Take care that the cup supporting the blade just grazes the ground. This will prevent the blade from touching the ound. 2 16 I1. Drawing out the string (A) During cutting, the nylon string wears naturally causing an increase in the speed of the engine and a reduced cutting capacity. When this happens, to bring out more string bump the head against the ground: release the throttle trigger to reduce the engine speed to less than 8000 rpm. Use of sawtooth blade 2 5 11 16 Do not attempt to cut trees with a larger than recommended diameter, to prevent the risk of kickback or damage to the blade. The sawtooth blade serves to cut bushes and small trees, with maximum diameter of seven centimeters. Rest the left side of the special shield on the trunk while cutting to limit the risk of losing control of the machine. L. Environmental information This section contains information useful for maintaining the characteristics of eco-compatibility included in the origin design of the machine, and as regards proper use and disposal of oil and fuel. Design In the design stage, care was taken to develop an engine with reduced consumption and low emissions of noise and pollutant exhaust fumes. Use of machine The operations of filling the tank with the fuel mix ture should be carried out in such a way as to avoid spilling fuel and contaminating the soil and environment. Periods of prolonged disuse Always empty the fuel tank with the same precautions used in filling it. Disposal Do not dispose inappropriately of the machine when it is no longer usable. Deliver it to an authorized organization for proper disposal in compliance with the regulations in force. ENGLISH - 8 M. Troubleshooting table Engine will not start Engine runs badlyor looses powerwhen cutting The machine runs but does not cut well Check STOP switch is in the position I. • Control fuel level min. 25%tank capacity. • • Check air filter is clean. • • Remove spark plug, dry it, clean it and adjust it, and replace it, if necessary. • • Change fuel filter. Contact your dealer. • Carefully follow the cutting accessory assembly instructions. • Check metal cutting accessory is sharp. Otherwise, contact your dealer. • The engine continues to have problems: contact your authorized supplier ENGLISH - 9 N. Declaration of conformity The undersigned, authorized by Electrolux Outdoor Products Italy S.P.A., declares that the following products model /TYPE: BC010A, BC010B starting from the serial numbers produced from 2003 on, manufactured by Electrolux Outdoor Products Italy S.P.A.., Valmadrera, Italia, comply with European Directive: 98/37/EEC (Machine Directive), 93/68/EEC (EEC Marking Directive) & 89/336/EEC (Electromagnetic Compatibility Directive), directive 2000/14/EEC (Enclosure V). Valmadrera, 15.12.03 Giuseppe Todero (Technical Manager) Electrolux Outdoor Products Italy S.P.A. Via Como 72, 23868 Valmadrera (Lecco) ITALY O. Technical data Displacement (cm3) ............................................................................................... 34 36 38 42 46 Bore (mm) .............................................................................................................. 38 40 40 41 43 Stroke (mm) ............................................................................................................. 30 30 30 30 30 Engine output (kW) (ISO 8893) ................................................................................ 1,2 1,25 1,3 1,6 1,8 Maximum shaft rotation frequency (min-1) ............................................................ 7.700 7.700 7.700 7.700 7.700 Rotation speed (frequency of rotation) of engine at maximum rotation frequency recommended for shaft (min-1) ...................................................................... 12.100 12.100 12.100 12.100 12.100 Engine speed at max power (min-1) ........................................................................... 8.000 8.000 8.000 8.000 8.200 Minim...

Herunterladen

Geben Sie zwei Ziffern: