Stimmen - 4, Durchschnittliche Bewertung: 3.8 ( )

Hersteller: Braun Dateigröße: 1.21 mb Dateiname: Unterrichtssprache:

So halten Sie Ihren Haarschneider in Bestform Nach jeder Anwendung den abgenommenen Distanzkamm leicht ausschutteln und mit der Burste reinigen. Drucken Sie die Entriegelungstaste (3), um das Schneidsystem (2) zu offnen. Reinigen Sie das Schneidsystem und das Innere des Haarschneiders mit dem Reinigungsburstchen (13). Um eine optimale Funktion des Schneidsystems zu gewahrleisten, muss es nach jedem Gebrauch mit Leichtmaschinenol geolt werden (D). Schneidsystem anschlie.end wieder auf das Gerat drucken, bis es einrastet. Zum Schutz des Kabels sollte es nach Gebrauch vom Gerat getrennt werden. Akkupflege (nur HC 50) Um die Kapazitat der Akku-Einheit zu erhalten, sollte das Gerat ca. alle 6 Monate durch regularen Gebrauch entladen werden. Danach wieder voll aufladen. Der Haarschneider sollte nicht permanent geladen werden. Das Gerat nicht langere Zeit Temperaturen uber 50 °C aussetzen. Umweltschutz (nur HC 50) Dieses Gerat enthalt eine Nickel-Hydrid-Akku-Einheit. Aus Umweltschutzgrunden darf das Gerat am Ende seiner Lebensdauer nicht mit dem Hausmull entsorgt werden. Offnen Sie das Gehause wie auf Seite 68 dargestellt; nehmen Sie die Akku-Einheit heraus und geben Sie sie gema. nationaler oder lokaler Bestimmungen beim Handel oder entsprechenden Sammelstellen ab. Anderungen vorbehalten. Dieses Gerat entspricht dem EMV-Gesetz (EG-Richtlinie (89/336/EWG) sowie der Niederspannungsrichtlinie (73/23 EWG). English Our products are designed to meet the highest standards of quality, functionality and design. We hope you enjoy your new Braun appliance. Important • Study the pictures and read the copy carefully before using the clipper. • Do not use the clipper near or over basins filled with water (e.g. bath tubs, showers etc.). • Do not wind the cord around the appliance. • For household use only. • When the distance comb is removed, the cutting system should not be pressed into the skin. Danger of injury! • After each use, clean and oil the cutting system (D). Description 1 Distance comb 2 Cutting system 3 Release button for cutting system 4 Length settings 5 Length selector 6 On/off switch 7 Pilot light (HC 50 only) 8 Cord socket 9 Adapter 10 Barber’s comb 11 Barber’s scissors 12 Light machine oil 13 Cleaning brush Technical specifications Power supply: 220–240 V ~ / 50–60 Hz Wattage: max. 7 W Charging the clipper (HC 50 only) Connect the clipper to the mains with the on/off switch (6) in position «off» and charge it for at least 8 hours. The pilot light (7) indicates that the clipper is connected to the mains. Once the clipper is completely charged, use it without the cord until discharged. Then recharge to full capacity again. A full charge will give up to 30 minutes of cordless trimming depending on your hair. However, the maximum capacity will only be reached after several charging/discharging cycles. Best environmental temperature range for charging is 15 °C to 35 °C. If the rechargeable battery is discharged, you may also operate the clipper via the mains cord. (If the clipper does not run immediately, charge it for approx. 1 minute in the «off» position.) General The person whose hair you want to cut should sit in a position where the top of the head is at your eye level. The hair should be clean, well combed, tangle-free and dry. Ensure you have a firm, but relaxed grip on the clipper. If you are not used to clipping hair, begin with a higher setting and then reduce the setting to avoid cutting more hair than desired. Use a slow and controlled movement. Do not force the clipper through the hair faster than the clipper can cut it. In between, shake or blow off the hair from the clipper. If too much hair is caught in the distance comb, remove and clean it. To control your progress during clipping, regularly comb the hair in the style desired. Normal clipping Push the distance comb (1) onto the hair clipper until it locks. The hair length selector (5) must be in position «1». To choose the desired length setting (4), push down the length selector and shift it upward. To start clipping, shift the on/off switch (6) to «on». Keep the distance comb flat on the hair, parallel to the head, and slowly move against the direction of hair growth. The distance comb can only be taken off when the length selector is set to «1». Clipping or trimming without distance comb Remove the distance comb (only possible at setting «1»). To start clipping, shift the on/off switch to «on». Move the cutting system only in a parallel position to the skin (A, cutting hair). Slowly and carefully move the appliance against the direction of hair growth. Only when trimming contours should the cutting system be positioned vertically (B, trimming). Make sure you do not tilt the appliance while it is touching the skin (C). Avoid jerky movements while cutting. Clipping with the barber’s comb To cut longer hair, hold it up with the barber’s comb (10) and cut it with the scissors (11) or with the clipper (distance comb must be removed from the clippe...

Herunterladen

Geben Sie zwei Ziffern: