Stimmen - 3, Durchschnittliche Bewertung: 4.7 ( )

Hersteller: Craftsman Dateigröße: 1.62 mb Dateiname: Unterrichtssprache:

Follow instructions for service. Keep handles dry, clean, and free from oil and grease, AVOID UNINTENTIONAL STARTING -Don't carry the appliance while holding the switch area. The unit is shipped partly charged, and may start inadvertently if not handled properly. CHECK DAMAGED PARTS -If any component of the appliance experiences a hard impact, check that no parts were damaged and verify that the unit operates properly. Check for misalignment or bending of moving parts,breakage ofparts,andanyother condition thatmayaffectoperation. Apartthatisdamagedbe shouldproperlyrepairedbyan orre-placed authorizedcenter. service STAYALERT-Watchwhatyouare doing.UsecommonDonot sense. operatethetoolwhenyouaretired. Storethesebyfolding instructionsin halfandslidingintotheslotintheback ofthewaltcharging rack. FORHOUSEHOLDONLY. USE SAVE THESE INSTRUCTIONS e" =A• ATTACHING THE SWEEPER TUBE Before using, slide the sweeper tube onto the main housing until the buttons on both sides of the housing snap into the corresponding openings in the tube. CONNECTING TOOL ATTACHMENT TO THE POWER HANDLE Be sure to follow the following safety precautions when attaching and detaching tools from the power handle. Remove the battery from the handle before attaching or detaching tools. Never touch the control switches on the power handle when attaching and detaching tools. To attach a tool: 1. Twist the lock ring on the power handle to the unlocked position. (see figure 1) Figure 1 2. Insert the male end of the power handle interface into the female socket in the end of the tool attachment making sure that it is firmly seated. (see figure 2) The interface is keyed so that it will only go together one way. The handle and tool should go together easily. If you experience resistance in putting them together, check that the keys on the handle are properly aligned with the slots in the tool. Figure 2 3. Grasp the tool attachment firmly with one hand (note, do not grasp on a rotating part such as the auxiliary handle), and twist the lock ring on the power handle to the locked position with the other hand. (see figure 3) Figure 3 To detach a tool: 1. Grasp the tool attachment firmly with one hand (note, do not grasp on a rotating part such as the auxiliary handle), and twist the lock ring on the power handle to the unlocked position with the other hand. (see figure 4) Figure 5 2. Insert the battery fully into the handle making sure that the spring- loaded buttons on each side of the battery pack snap into place in the handle. Removing the Battery 1. Depress the spring-loaded buttons on both sides of the battery simultaneously. (see figure 6) Figure 4 2. Pull the power handle and tool attachment apart. The power handle and tool attachment should separate easily. If they do not, check to be sure that the lock ring is in the fully unlocked position. Attaching the Battery 1. Align the rib on the battery pack with the corresponding slot in the end of the power handle. (see figure 5) Figure 6 2. Pull the battery pack straight out from the handle. To turn the tool on: 1. Grip the control grip firmly with one hand and grip the auxiliary handle on the tool attachment (if provided) with the other hand. 2. Push the trigger that your thumb rests on straight forward, this is the safety release. (see figure 7) attachmentas inthewaltbracketshownforconvenient(see storage. figure9) Figure7 3.Whileholdingtheswitchunderyour thumbintheforwardposition,useyour fingerstopullupwardonthecontrol trigger.(seefigure8)Thiswillenergizethetoolandallowyoutodoyourwork. ItisNOTnecessary tokeeppressure onthethumbswitchafterthetoolhas started. Pleasenotethatthetoolwillnotstart ifthelockringisnotinthefullylockedposition. Figure8 To turn the tool off: 1. Release the control trigger and the tool wilt turn off. The thumb switch wilt return to the rear position to prevent accidental re-starting of the tool. WALL BRACKET Mount the wall bracket securely to the wall; attach with screws to a wall stud. The use of wall board anchors is NOT recommended. Place the tool Figure 9 A A_. WARNING: Always remove the battery when performing any maintenance on the sweeper attachment. WARNING: Always keep hands away from the triggers when performing maintenance on the sweeper. LUBRICATION -No periodic lubrication of the sweeper attachment is required. CLEANING OF PLASTIC PARTS -Use only a dry brush or a cloth with warm water and mild soap to clean plastic parts. Many household cleaners contain chemicals which could damage the plastic. Never use gasoline, turpentine, paint thinner or similar fluids. Never spray-wash tool or immerse in water. Water or liquid inside the tool can cause serious damage to the unit. DROPPING THE UNIT -If you drop the unit, carefully inspect it for any damage before using it again. Have the unit professionally repaired if damage has occurred. 0= A TEMPERATU RE = Temperature extremes limit the useful life of the battery. The best storage place is one that is cool and dry. Store the tool...

Herunterladen

Geben Sie zwei Ziffern: