Stimmen - 3, Durchschnittliche Bewertung: 5 ( )

Hersteller: Black & Decker Dateigröße: 2.57 mb Dateiname: Unterrichtssprache:

Fotos und technische Daten  Black & Decker  CST800

MOUNTING THE CHARGER BRACKET 1. If you intend to mount, the charger bracket on a wall, follow the instructions listed below. 2. Remove the two screws and plastic anchors from the plastic bag. 3. Use the charger bracket to mark the locations of the holes required. Be sure to mount the bracket high enough so that the trimmer can hang freely from it; about 4 feet (1.2m) from the floor. 4. Drill a .250” (6 mm) diameter hole at each marked location. 5. Insert the plastic anchors into the holes and insert one of the screws in each one. Tighten the screws until the heads are above the anchors just enough so that the charger bracket will fit between the anchor and the screw head. 6. Place the charger bracket on the wall (narrow end up) and make sure that the power cord is positioned in the side slot. Press the charger bracket over the screw heads and slide it down until it sits firmly on the screws. 7. Firmly tighten both screws. LED INDICATOR LIGHT The unit is equipped with a red LED charging indicator light, located on the upper left side of the unit (Figure 1). The indicator light will come on when the unit is properly connected to the charging base and the power plug is inserted into the electrical outlet. The light will remain on, so long as the unit is properly connected to the powered charging base. It is recommended to store the unit on the charger during the growing season, with the charger plugged in, to have the battery charged for the next use. TO CHARGE YOUR BATTERY, FOLLOW THE STEPS BELOW 1. Install the trimmer onto the charger bracket by positioning the handle cavity, shown in Figure 7 over the hook of the charger bracket. 2. Rotate the trimmer down, keeping the hook engaged with the handle cavity, and position the charge port over the bracket’s charge pin (figure 7). 3. Plug the charger into any standard 120 volt, 60Hz outlet. Charging will be automatically controlled until you remove the trimmer from the bracket. 4. It is recommended that the trimmer be left on charge, during the growing season. For winter or otherextended periods of storage, it is recommended that the unit be fully charged prior to storage. OPERATING INSTRUCTIONS • CAUTION: ALWAYS WEAR EYE PROTECTION. • CAUTION: Inspect area to be trimmed and remove any wire, cord, or string-like objects which could become entangled in the rotating line or spool. Be particularly careful to avoid any wire which might be bent outwardly into the path of the tool, such as barbs at the base of a chain link fence. • To turn trimmer on, pull back on the lock out button, shown in Figure 1, at the same time, squeeze the trigger switch. To turn the tool off, release the trigger switch. • Angle unit as shown in Figure 5. • Slowly swing trimmer side-to-side as shown in Figure 6. CUTTING LINE LINE FEEDING Your trimmer only uses .065” (1.65 mm) diameter, ROUND nylon line to cut grass and weeds quickly and easily. During use, the tip of the nylon line will become frayed and worn. Gently bump the feed head of the trimmer on the ground to release a fresh length of line. Cutting line will wear faster and require more feeding if the cutting is done along sidewalks or other abrasive surfaces or heavier weeds are being cut. CLEARING JAMS AND TANGLED LINES From time to time, especially when cutting thick or stalky weeds, the line feeding hub may become clogged with sap or other material and the line will become jammed as a result. To clear the jam, follow the steps listed below. 1. Turn the unit upside down. 2. Press the release tabs on the line hub cover and remove by pulling it straight off (Figure 8). 3. Lift the spool of nylon line out of the hub and clear any broken line or cutting debris from the spool area. (If you plan to replace the spool or rewind it, this is the place to do so, otherwise, move on.) 4. Unwrap about one foot (30 cm) of line to ensure that it’s undamaged. If it is okay, rewind it and insert the line end through the eyelet in the spool hub as shown in figure 9. Ensure the spring is in place under the spool. Pull the line through the hole to maintain tension while placing the spool down into the hub with the arrow up, as shown in figure 9. 5. Press the spool down GENTLY on the spring and rotate it until you feel it drop into place. Take care to keep the line from becoming trapped under the spool. 6. Snap the hub cap back on hold the tool in the trimming position, and turn the tool on. In a few seconds or less you’ll hear the nylon line being cut to the proper length; if not bump the feed head gently on the ground to initiate a fresh length of line. SPOOL OR LINE REPLACEMENT (Use 0.065” diameter ROUND line only.) 1. Turn the unit upside down. 2. Press the release tabs on the line hub cap, as shown in Figure 8 and remove the cap by pulling it straight off. 3. Remove the spool from the tool and remove and discard all line on spool. 4. Choose either OPTION 1 or OPTION 2 below for spool or line replacement. 5. Insert the line end through the eyelet in...

Herunterladen

Geben Sie zwei Ziffern: