Stimmen - 4, Durchschnittliche Bewertung: 4 ( )

Hersteller: Makita Dateigröße: 1.38 mb Dateiname: UM140D.pdf Unterrichtssprache:

ADDITIONAL SAFETY RULES FOFq BATTERY the Makita battery 122. 5. Do not charge inside a box or container of any kind 6 . Do not short the battery: 3) Do not expose battery to water or rain. 4) Do not cut the adaptor cord. away. Replace it with a new one. release of injurious material. 12 5 ADDITIONAL SAFETY RULES FOR CHARGER 1 . The Makita charger Model DC122 is specifically designed to charge only the Makita battery 121 or 122. Do not attempt t o charge any other battery with this charger. 2. Handle the charger carefully. Do not drop or strike it. 3. Never carry the charger by cord or yank it to disconnect from receptacle. 4. Keep cord from heat, oil, chemicals, and sharp edges. 5. Use only a power source of the same voltage a s indicated on the nameplate 6. Do not attempt to use a step-up transformer, an engine generator or DC 7 . Charge the battery at a room temperature of 10°C ( 5 O O F ) - 4OoC ( 1 0 4 O F ) . 8. Do not charge in place exposed to direct sunlight. 9. Do not allow the charger to get wet. IO. Do not charge inside a box or container of any kind. 1 1 . Do not charge near volatile, flammable material such a s gasoline, paint, gas, 12. Do not charge on top of paper, carpet, vinyl sheeting, cloth materials, etc. 13. Do not allow anything to cover or clog the charger vents. Do not attempt 14. Do not charge in dusty place. 15. Stop charging immediately if you notice anything abnormal. Ship or take the charger and the battery to your nearest Makita Service Center or Distributor for checking them. of the charger when charging. power receptacle. adhesive, etc. to insert anything into the vents. 16. Do not attempt to disassemble or make modifications to the charger. 1 7 . Do not put any metal objects or foreign matter into the inlet of the charger. Short-circuit will occur, causing a burn injury and charger breakdown. SAVE THESE INSTRUCTIONS. Operation Hold/support t h e tool firmly with the grip and loop handle. Switch ON only when the blades are not contacting the ground. Cut an even swath while swinging the tool from right to left, angling the cutting head slightly while doing so. When cutting grass or weeds next to walls, curbs, sidewalks and the like, move the tool slowly and smooth I y a Io ng them. Swith t h e tool from right to left 6 1 1 Switch action To prevent the trigger from being accidentally pulled, a lock-off button is provided. To start the tool, push in the lock-off button and pull the trigger. Release the trigger to stop. Lock-off button I Switch trigger I CAUTION: 0 Before connecting the battery to the tool, always check to see that the switch trigger 0 Do not switch on the tool when someone is nearby or when the blades are contacting actuates properly and returns to the “OFF” position when released, the ground. Connecting the battery to the tool Connect the battery to the tool using the adaptor cord. To prevent the adaptor cord from being accidentally disconnected, hook the cord to both strain relief hooks on the tool and the battery. //I Straight relief hook Adaptor cord I Strain relief hook Carrying the battery Hook the battery to your waist belt. If the adaptor cord is too long for your work, use the band provided to hold it when you coil it shorter. 10 Charging Connect the battery to the charger using the adaptor cord. Thc power source. The charging light will illuminate and charging ing light goes out at a certain time, the charging is complete. U I (Note: Refer to the table below for the charging time.) Charger DC122 Approx. 1 hour AoDrox. 2 hours Battery 121 Outlet Batterv-, , Charger CAUTION: Always charge the Makita battery 122 immediately after purc .Always recharge the Makita battery 122 after use. If the Makita battery 122 has not been used for long periods, time specified in the table above. (Example: If it has not been i it for approx. one week). Charging continues even after the ch, battery is left uncharged for more than six months, it may be light does not come on within five minutes after you start the be unchargeable. Ship or take the charger and the battery to y Center or Distributor for checking. plug the charger into the i l l begin. When the chargllug the charger. DC121 ox. 4 hours Connector Adaptor cord light ise. large it for more than the ?d for six months, charge ging light goes out. If the ,me unchargeable. I f the harging, the battery may u r nearest Makita Service 7 Installing the safety guard (safety cover) Install the safety guard on the motor housing as shown in the figure. Then secure the safety guard with the screw. Install the blades onto the pins. Turn the cap and the blade retainer clockwise until the pins fit into the holes in the blade retainer with a little click. 1 \ L S c r e w d r i v e r Safety guard I Installing t h e loop handle Install the loop handle on the shaft at the desired position. Then secure the loop handle with the screw. Adjusting the grip position The grip position can be adjusted approx. 100 mm (3-15/16"). Loosen the cl...

Herunterladen

Geben Sie zwei Ziffern: