Stimmen - 4, Durchschnittliche Bewertung: 3.8
(
)
)
|
Anleitung Zusammenfassung
2. There are 3 holes on the wall bracket. Position the wall bracket with the two holes at the top. See Fig H. 3. Ensure that when the trimmer is attached the bottom of the trimmer is within 4 inches (100 mm) of the ground, this will make it easier to hang the trimmer and will also ensure that the wall bracket is within easy reach of an electric socket to allow the charger to be plugged in. 4. Fix wall bracket securely to the wall with the plugs and screws provided. 5. Your cordless trimmer can now be attached to the wall bracket for charging. Initial Charging Procedure 1. Use the charger indoors only. 2. Ensure the charger is not exposed to moisture. Keep the charger and the trimmer dry at all times. Keep the charger well ventilated during charging. 3. Ensure the trimmer is correctly located into the wall bracket (G2) and the charge connector (H1). 4. Plug the charger (G1) into a suitable household electrical wall socket and switch on. 5. The red indicator lamp glows continuously during charging. 6. Full charge will be achieved in 24 hours. During charging the charger becomes warm. This is normal and means the charger is operating correctly. Re-Charging Your Cordless Trimmer 1. Re-charge the battery as soon as the cutting power of your cordless trimmer begins to die and slow down. 2. Avoid running the cordless trimmer into "deep" dis- charge, i.e. avoid flattening the battery completely. 3. Follow the procedure outlined in the Initial Charging Procedure. 4. Charging the battery according to these instructions should ensure maximum battery life. H 1 • The battery should be charged for 24 hours before use. • Re-charge your cordless trimmer immediately after every use for the full 24 hour charging period. • The cordless trimmer can be left connected to the charger permanently, with the charger switched on, without fear of overcharging. • The charger will automatically keep the battery topped up with charge during storage and will ensure that the cordless trimmer is ready for use. nut (if applicable) 4 Adjustment To adjust the handle length (J & K) 1. Loosen the height adjust knob. (fig J) 2. Adjust length of the handle to the most comfortable operating position (fig K). 3. Re-tighten the height adjust knob. J height K adjust knob Auto Line Feed System 1. A short length of new line is fed out every time you L switch on, this is caused by the cutting head accelerating up to its full speed. 2. To feed more line, it is necessary to switch-off, allow the motor to stop and then restart. When edging do this frequently. 3. When the line feeds you will hear a change in the motor sound as well as the noise generated by the line being cut to its length. 4. If the line does not feed see Fault Finding Chart for further information. line cutter How to trim and edge WARNING The use of eye protection is recommended. Do not lean over the trimmer whilst trimming or edging, objects may be thrown by the cutting line. Do not allow cutting head to rest on the ground. Do not overload your trimmer. Overloading can be avoided by making sure the motor speed does not drop unduly. Disconnect from the mains electricity supply before attempting any maintenance or adjustment. BEFORE USE • Make sure that the line is fed out. • Make sure motor is up to full speed before trimming or edging. To start your trimmer • The switchbox is provided with a lock-off button (M1) to prevent accidental starting. 1. To start, press lock-off button (M1), squeeze the switch lever (M2), release lock-off button. How to trim 1. Cut with nylon line at an angle using the tip. See Fig N. 2. Swing trimmer in and out of the cutting area taking small cuts (P) 3. Line is fed out automatically every time the trimmer head stops rotating and returns to operating speed. • Extra line can be fed out manually as described on page 5. 4. To stop your trimmer release the switch lever (M2). How to edge 1. To convert to edging mode, depress locking button and twist head anti-clockwise until arrow lines up with "EDGE". An audible "click" will confirm that the head is locked. Ensure the button has returned to its original position. See Fig Q. 2. Rest edger on roller for extra stability and line up with edge of lawn. See Fig R. Edge in direction indicated in Fig S. so that debris is thrown away from you. 3. To return to trimming mode, depress locking button and twist head clockwise until arrow lines up with "TRIM". An audible "click" will confirm that the head is locked. Ensure the button has returned to its original position. See Fig T. M 1 N 2 P Q R S T 5 Fault Finding Chart WARNING Avoid accidental starting, keep hands and fingers away from the switch lever whilst attempting any maintenance or adjustment. 5 Fault Finding Chart WARNING Avoid accidental starting, keep hands and fingers away from the switch lever whilst attempting any maintenance or adjustment. FAULT CHECK ACTION Is the automatic line feed working? Manually feed out line. SEE “MANUAL LINE FEED” Is the line fed out and...