Stimmen - 2, Durchschnittliche Bewertung: 3 ( )

Hersteller: Husqvarna Dateigröße: 309.09 kb Dateiname: HOUS2005_O0501501.pdf Unterrichtssprache:

Fotos und technische Daten  Husqvarna  125C

Slowly pull out the cord with your right hand until you feel some resistance (the starter pawls grip); then quickly and powerfully pull the cord. Never wrap the starter cord aroundyour hand. Repeat pulling the cord until the engine attempts to start. Squeeze throttle trigger to release the choke and pull starter rope until engine runs. NOTE: If engine dies, return blue engine choke lever to the closed position and repeat starting steps. CAUTION! Do not pull the starter cord all the way out and do not let go of the starter handle when the cord is fully extended. This can damage the machine. 14 STARTING AND STOPPING Warm engine With a warm engine, squeeze and hold the throttle trigger. Pull starter rope sharply while squeezing throttle trigger until engine runs. Stopping Stop the engine by pushing and holding the stop switch in the STOP position until the engine stops. WARNING!Whentheengineisstartedwiththechokeintheclosedpositionthecuttingattachmentwillstarttorotateimmediately. 15 MAINTENANCE The owner is responsible for the performance of all required maintenance as defined in the operator’s manual. Carburetor Your Husqvarna product has been designed and manufactured to specifications that reduce harmful emissions. After the engine has used 8- --10 tanks of fuel, the engine will be run- --in. To ensure that it continues to run at peak performance and to minimize harmful exhaust emissions after the run- --in period, ask your servicing dealer to adjust your carburetor. WARNING! The complete clutch, clutch cover, and shaft must be fitted before the machine is started, otherwise parts could come loose and cause personal injury. The idle speed is correctly adjusted when the engine will run smoothly in every position. The idle speed should also be well below the speed at which the cutting attachment starts to rotate. WARNING!Iftheidlespeedcan- notbeadjustedsothatthecuttingattachmentstops,contactyourser- vicingdealer.Donotusethema- chineuntilithasbeencorrectlyad- justedorrepaired. Idle Speed Screw- --T Function S The carburetor governs the engine’s speed via the throttle control. Air and fuel are mixed in the carburetor. S The T- --screw regulates the throttle setting at idle speed. If the T- --screw is turned clockwise this gives a higher idle speed; turning it counterclockwise gives a lower idle speed. Basic setting S The basic carburetor settings are adjusted during testing at the factory. Fine adjustment should be carried out by a skilled technician. CAUTION! If the cutting attachment rotates when the engine is idling the idle adjustment screw T should be turned counterclockwise until the cutting attachment stops. Rec. idle speed: See “Technical data” section. Recommended max. speed: See “Technical data” section. WARNING! If theidlespeed cannot be adjusted so that the cutting attachment stops, contact your dealer/service workshop. Do not use the machine until it has been correctly adjusted or repaired. Fine adjustment of the idle speed- --T Adjust the idle speed using the idle adjustment screw- --T if it is necessary to readjust. First, turn the idle adjustment screw- --T clockwise until the cutting attachment starts to rotate. Then, turn the screw counterclockwise until the cutting attachment stops. Unit/Maintenance Safety Disconnect the spark plug before performing maintenance, except carburetor adjustments. Muffler CAUTION! Muffler is fitted with a catalytic converter designed to reduce harmful exhaust gases. The muffler is designed to reduce the noise level and to direct the exhaust gases away from the operator. The exhaust gases are hot and can contain sparks, which may cause fire if directed against dry and combustible material. Mufflers are equipped with a special spark arrestor mesh. The mesh should be checked and, if necessary. cleaned by a servicing dealer. If the mesh is damaged, it should be replaced. If themeshis frequently blocked, this can be a sign that the performance of the catalytic converter is impaired. Contact your servicing dealer to inspect the muffler. A blocked mesh will cause the machine to overheat and result in damage to the cylinder and piston. 16 MAINTENANCE MufflerboltsCAUTION!Neveruseamachinethathas a faulty or loose muffler. Ensure the muffler bolts are tight. WARNING! Mufflers fitted with catalytic converters get very hot during use and remain so for some time after stopping. This also applies at idle speed. Contact can result in burns to the skin. Remember theriskof fire! WARNING! The inside of the muffler contain chemicals that may be carcinogenic. Avoid contact with these elements in the event of a damaged muffler. WARNING! Bear in mind that: Engine exhaust fumes contain carbon monoxide, which can cause carbon monoxide poisoning. For this reason you should not start or run the machine indoors, or anywhere that is poorly ventilated. The exhaust fumes from the engine are hot and may contain sparks which can start a fire. Never start the machine indoors or near combustible mat...

Herunterladen

Geben Sie zwei Ziffern: