Stimmen - 2, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
X Check that the stop switch works correctly. X Check that the handle and handlebar are undamaged and secured correctly. X Check that the cutting attachment does not rotate at idle. X Clean the air filter. Replace if necessary. X Check that the guard is undamaged and not cracked. Replace the guard if it has been exposed to impact or is cracked. X Check that the trimmer head is undamaged and not cracked. Replace the trimmer head if necessary. X Check that the locking nut of the cutting equipment is tighten correctly. X Check that nuts and screws are tight. X Check that there are no fuel leaks from the engine, tank or fuel lines. X Check the engine oil level and top up if necessary. X Check the starter and starter cord. X Check that the vibration damping elements are not damaged. X Clean the outside of the spark plug. Remove it and check the electrode gap. Adjust the gap to 0,6-0,7 mm or replace the spark plug. Check that the spark plug is fitted with a suppressor. X Clean the machine’s cooling system. X Clean or replace the spark arrestor mesh on the muffler (only applies to mufflers without a catalytic converter). X Clean the outside of the carburettor and the space around it. X Check that the bevel gear is filled three-quarters full with lubricant. Fill if necessary using special grease. X Check the fuel filter from contamination and the fuel hose from cracks or other defects. Replace if necessary. X Check all cables and connections. X Check the clutch, clutch springs and the clutch drum for wear. Replace if necessary by an autorized service workshop. X Replace the spark plug. Check that the spark plug is fitted with a suppressor. X Check and clean the spark arrestor mesh on the muffler (only applies to mufflers fitted with a catalytic converter). X Change the engine oil. X 22 – English Technical data TECHNICAL DATA 324LDx Engine Cylinder displacement, cm3 25,0 Cylinder bore, mm 35 Stroke, mm 26 Idle speed, rpm 3100 Recommended max. speed, rpm 11000 Speed of output shaft, rpm 8300 Max. engine output, acc. to ISO 8893, kW/ rpm 0,8 / 7000 Catalytic converter muffler No Speed-regulated ignition system No Ignition system Spark plug NGK CMR5H Electrode gap, mm 0,6 Fuel and lubrication system Fuel tank capacity, litre 0,5 Weight Weight without fuel, cutting attachment and guard, kg 5,4 Noise emissions (see note 1) Sound power level, measured dB(A) 106 Sound power level, guaranteed LWA dB(A) 107 Noise levels (see note 2) Equivalent sound pressure level at the operator’s ear, measured according to EN ISO 11806 and ISO 22868, dB(A): Equipped with trimmer head (original) 97 Vibration levels (see note 3) Equivalent vibration levels (ahv,eq) at handles, measured according to EN ISO 11806 and ISO 22867, m/s2 Equipped with trimmer head (original), left/right 4,1/4,1 Note 1: Noise emissions in the environment measured as sound power (LWA) in conformity with EC directive 2000/14/ EC. Reported sound power level for the machine has been measured with the original cutting attachment that gives the highest level. The difference between guaranteed and measured sound power is that the guaranteed sound power also includes dispersion in the measurement result and the variations between different machines of the same model according to Directive 2000/14/EC. Note 2: Reported data for equivalent sound pressure level for the machine has a typical statistical dispersion (standard deviation) of 1 dB (A). Note 3: Reported data for equivalent vibration level has a typical statistical dispersion (standard deviation) of 1 m/s2. English – 23 TECHNICAL DATA Approved accessories Type Cutting attachment guard, Art. no. Blade shaft thread M10 Plastic blades Tricut O 255 mm (Separate blades have part number 531 01 77-15) 503 93 42-02 / 503 97 71-01 Tricut O 300 mm (Separate blades have part number 531 01 77-15) 503 93 42-02 Trimmy Fix (O 2.4 mm cord) 503 93 42-02 / 503 97 71-01 Superauto II (O 2.4 - 2.7 mm cord) 503 93 42-02 / 503 97 71-01 Trimmer head S35 (O 2.4 - 3.0 mm cord) 503 93 42-02 / 503 97 71-01 T25 (O 2.0 - 2.7 mm cord) 503 93 42-02 / 503 97 71-01 T35, T35x (O 2.4 - 3.0 mm cord) 503 93 42-02 / 503 97 71-01 The following attachments are recommended for the specified models. Approved accessories Art No. Use with Clean sweep attachment with shaft SR600 537 19 67-01 324LDx Hedge trimmer attachment with shaft HA 110 537 19 66-01 324LDx Hedge trimmer attachment with shaft HA 850 537 19 66-02 324LDx Edger attachment with shaft 537 19 69-01 324LDx Saw attachment with shaft PA 1100 537 18 33-16 324LDx Trimmer attachment with shaft TA 850 537 35 35-01 324LDx The following attachments have been developed mainly for the Husqvarna 125LD trimmer, but can also be used with the specified models. Approved accessories Art No. Use with Cultivator attachment CAC 952 71 19-07 324LDx Edger attachment EAC 952 71 19-08 324LDx Pole saw attachment PAC 952 71 19-10 324LDx Blower attachment BAC 952 71 19-11 324LDx Hedge trimmer attachment HAC 952 71 19-21 324LDx...