– Do not expose the set, CDs, batteries or cassettes to humidity, rain, sand, direct sunlight or other places where high temperatures can occur, such as in the vicinity of heating apparatus or in motor cars parked in the sun. – Do not cover the set. The amplifier produces heat which must dissipate freely, so make sure that there is sufficient ventilation around the set. A minimum gap of 15 cm is necessary. – The mechanical parts of the CD player and the cassette deck contain self-lubricating bea

Tuner reception 1 Adjust the source selector to FM or AM. 2 Turn TUNING to tune to a station. • For FM, pull out the telescopic antenna. Incline and turn the antenna. Reduce its length if the signal is too strong (very close to a transmitter). • For AM, the set is provided with a built-in antenna so the telescopic antenna is not needed. Direct the antenna by turning the whole set. 3 To switch off the radio, adjust the source selector to OFF position. CD player Display indication for CD functions

Playing a CD is then not possible. Do not attempt to clean the lens but leave the set in a warm environment until the moisture evaporates. • Always shut the CD door to keep the CD compartment dust-free.To clean, dust the compartment with a soft dry cloth. • To take a CD out of its box, press the center spindle while lifting the CD.Always pick up the CD by the edge and replace the CD back in its box after use to avoid scratching and dust. • To clean the CD, wipe in a straight line from the center

• To stop a started timer recording, press the STOP/EJECT button on the VCR. • If the power fails for more than one minute, programmed timer recordings may be lost. Reset the clock before resetting the timer recordings. • If you are using a Cable Box/DBS, timer recordings are programmed differently. See page eight for details. See page 54 for more hints. VRZ342comb.QX33 4/7/99 10:06 PM Page 44 44 Rerecording (Tape Duplication) 1. Audio cable from AUDIO OUT Jack of VCR 1 to AUDIO IN Jack of VCR 2

Do not use this (polarized) plug with an extension cord, receptacle or other outlet unless the blades can be fully inserted to prevent blade exposure. 12-Power Cord Protection Pr,,.v<” -JDpiy cords walked on or pinched by items placed upon or against them, paying particular attention to cords and plugs, convenience receptaoes aryl t^e point where they exit from the appliance 13.Cleaning - The appliance should be cleaned only as recommended by the manufacturer 14.Powor Lines - An outdoor ante

Québec H4T1E1 W (514)342-9180 (514)342-9372 VANCOUVER ';!4~ :• rdvew Hiçhway Va-c^.e- 6 С. V5M 2G7 W16041435-4411 1504)435 9911 MAGNAVOX AZ 8289 Stereo Cassette flayer Toll Free Help Line Ligne ¿'assistance en service libre Línea de ayuda telefónica sin cargo 800-531-0039 3133106 '-:54 : printed in Hong <0^ SRP 9517/I87337T001 PHILIPS CONSUMER ELECTRONICS COMPANY A Division of PM'ps Electronics North America Corporation Kncxvii’e. Tennessee 37914-1B,0. U S A. Canada English: Th

If it does not, consult your dealer or service organisation. If the set is equipped with a VOLTAGE (x) selector, the AC power voltage will be indicated next to it. Set this selector to the local AC power voltage. 2 Connect the power lead to the outlet AC MAINS and the wall jack. The AC power supply is switched on. • To disconnect the set from the power completely, withdraw the power plug from the wall outlet. see fig. 12-15 SHUFFLE - playing in random order 1 Press SHUFFLE before or during

If – – : – – appears on the display panel after you turn off the VCR, the VCR could not find the time. Use a different method to set the clock. • When the power plug is connected to an AC outlet, the correct time will appear on the display panel of the VCR when the power is off. • Press the EXIT/STATUS button repeatedly to make the time appear on the display panel when the VCR power is on. Helpful Hints 16 Setting the Clock (cont’d) Manual PBS Channel Selection 7 VCRTV VCR/TV QUICK PROGRAMMING P

If the remote control doesn’t operate your TV now, follow the steps below. 1 Point the remote control at your TV and press the TV button. Then, press the POWER button. If your TV turns on or off, try the other TV buttons (see pages 20 - 21). If your TV doesn’t turn on or off, or if the other buttons don’t work, go to step 2. 2 Find the brand of your TV on the list below, and remember the two-digit number beside it. 1&6 2 1&6 2 Find your TV code. 4 5 3 REW PLAY POWER VCR PLUS+ /ENTER SPEED VCR TI