Stimmen - 4, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
The stereo will not operate when you remove its anti theft control panel. You can quickly remove and store the control panel in the supplied carry case and take it with you for added security. The stereo's features include: Front CD IN Jack - lets you quickly connect a portable CD player to the stereo, so you can play your favorite CDs in your vehicle. Auto-Stop - stop's the tape when it reaches the end, to reduce wear on your tape and the cassette deck. Tone and Balance Controls - lets you adjust high and low sounds and the balance between left/right speakers, so you can tailor the sound to suit your preferences Metal/CrO2 - takes advantage of the improved sound quality of metal or CrO2 tapes. Mono/Stereo Control - lets you select FM reception in stereo on strong stations or monaural reception on weak stations. Push Band Selector - lets you easily select an AM or FM station with the push of a button. Built-In Noise-Suppression - reduces the noise caused by your vehicle's Choke electrical system. For your permanent records, we recommend you record your stereo's serial number in the space below. The serial number is on the top of the stereo. Serial Number: ________________________________ AM/FM Stereo Cassette Player (120-2117) Installation Faxback Doc. # 57141 Before You Begin The Installation Before you install your stereo, we recommend you read through all the instructions in this owner's manual. You should be able to answer all of these questions about your vehicle's electrical and sound systems. Which terminal in my vehicle's fuse box supplies power even when the ignition is turned off? Which terminal in my vehicle's fuse box is for accessories? How do I connect a wire to the fuse box? Which stereo wires are line-level outputs and which are speaker outputs? Also, be aware that installation in your vehicle might require cutting or modifying your vehicle. Note: Before permanent installation, we recommend that you install the stereo by temporarily connecting it to ground and power, optional components, and your speakers. Then test the connections. Next disconnect the stereo, mount it in your vehicle, and then reconnect it. Place the stereo as close as possible to the selected mounting location when making the temporary connections. CAUTION: Be sure your speakers can handle 14 watts of power (7 watts per channel). Each speaker must have an impedance of at least 4 Ohms. Your local RadioShack store carries a full line of speakers. Preparing the Mounting Area Before you mount the stereo, make sure you have all the necessary materials. Then confirm that the stereo fits your vehicle's stereo mounting area. This auto-sound stereo system is a DIN-E size unit that requires a 2-1/16-inch high by 7-3/16-inch wide by 6-11/16-inch deep (52 x 182 x 170 mm) mounting area. Note: If the mounting area is too large, you might be able to mount the stereo with an in-dash installation kit, available at your local RadioShack store. Follow the installation kit's instructions to mount the stereo. CAUTION: Be careful to avoid obstructions behind the mounting surface. Routing Speaker Wire If you install speakers, avoid routing the speaker wires near moving parts or sharp edges. You can usually route them along the wiring channel beneath the vehicle's door facing by carefully removing the molding that holds the carpet in place. After you route the speaker wires, replace the molding. Testing the Stereo Before you mount the stereo or any speaker, test the stereo by temporarily connecting the power wire, speakers, and antenna as described in "Making the Connections," below. If you plan to use an adapter harness to connect the stereo, see "Using an Adapter Harness," below. Making The Connections The supplied harness with the 14-pin connector includes all the lead wires you need to connect the stereo to ground, power, optional components, and speakers. IMPORTANT: Do not cut these wires. If you cut any wire, you cannot obtain a refund or exchange on this product. However, your local Radio Shack store will provide warranty service if you cut a wire and find the product is defective. Depending on your individual auto sound system, you might need additional wire to complete connections. Your local RadioShack store carries a full line of wire and wire management accessories. CAUTIONS: For added safety and to protect your stereo, remember to disconnect the cable from your vehicle battery's negative (-) terminal before you begin making the connections. You must connect the ground and primary wires first, then make all other connections before you plug the 14-wire harness into the stereo. (See "Using an Adapter Harness," below.) If you do not make connections in the order shown, damage to the stereo is possible if any wire connections are made incorrectly. You must connect a separate wire to each speaker terminal as described in the following procedure. Do not use a common wire or chassis ground for any speaker connection. Using an Adapter Harnes...