Stimmen - 2, Durchschnittliche Bewertung: 5
(
)
)
|
Anleitung Zusammenfassung
• Some disc changers need conversion cords for connection. See the section on "Safety Precautions" for details. — 17 — Connecting English Front left output (KRC-408 only) Rear left output (White) Front right output (Red) (KRC-408 only) Fuse (10A) Rear right output (Red) – + – – – + – + FRONT • L FRONT • R REAR • L REAR • R P.CONT ANT.CONT When only two speakers are being connected to the system, connect the connectors either to both the front output terminals or to both the rear output terminals (do not mix front and rear). For example, if you connect the + connector of the left speaker to a front output terminal, do not connect the - connector to a rear output terminal. 2CAUTION If you connect the ignition wire (red) and the battery wire (yellow) to the car chassis (ground), you may cause a short circuit, that in turn may start a fire. Always connect those wires to the power source running through the fuse box. 2WARNING FM/AM antenna input KENWOOD disc changer control input Wiring harness (Accessory1) White/Black Gray/Black Green/Black Purple/Black White Gray Green Purple To front left speaker To front right speaker To rear right speaker To rear left speaker Power control/Motor antenna control wire (Blue/White) Ignition wire (Red) Battery wire (Yellow) Ground wire (Black) · (To car chassis) Ignition key switch Car fuse box (Main fuse) ACC Car fuse box Battery If no connections are made, do not let the wire come To connect the Disc changer, consult your Disc changer manual. NOTE Depending on what antenna you are using, connect either to the control terminal of the motor antenna, or to the power terminal for the booster amplifier of the film-type antenna. + + — 18 — Installation Installation Installing in Firewall or metal support Accessory4 8 mm MAX. o5mm o5mm 8mm MAX. T: Toyota cars N: Nissan cars T N N T T/N Accessory5...for Nissan car Accessory6 ...for Toyota car Refer to the section “ Removing the hard ” and then remove the Align the holes in the unit vehicle mounting bracket and accessory screws. 2 1 5 6 Bend the tabs of the mounting sleeve with a screwdriver or similar utensil and Self-tapping Accessory2 attach it in place. 2CAUTION screw Metal mounting • During installation, do not use any screws except for those (commerciall strap provided. The use of different screws might result in damage y available) the main unit. • Damage may occur if a screwdriver or similar tool is used with excessive force during the installations. NOTE Make sure that the unit is installed securely in place. If the unit is unstable, it may malfunction (for example, the sound may skip). — 19 — Installation Removing Removing English 1 Engage the catch locks on the lower level. Lower the frame and pull Catch Lock Accessory3 Removal tool 2 When the lower level is removed, remove the upper locations. The frame can be removed from the top side in the same manner. Accessory3 Removal tool Accessory4 Lower the removal tool toward the bottom, and pull out the unit halfway whilst pressing towards the inside. 4 Pull the unit all the way out with your hands, being careful not to drop it. 5 Be careful to avoid injury from the catch pins on the removal tool. Catch facing up Refer to the section “ Removing the hard ” and then remove the Remove the Hex-head screw on the back panel. Insert the two removal tools deeply as shown. 3 2 1 NOTE 2CAUTION — 20 — Installation Screwing If you want to fasten does not fall off, screw o4 . 16 mm) in the hole shown below. Accessory7 2CAUTION Never insert the taptite screw ( o4 . 16 mm) in any other screw hole than the one specified. If you screw it in another hole, contact and may cause damage to the mechanical parts inside the unit. — 21 — Troubleshooting What might Before calling PROBLEM POSSIBLE CAUSE SOLUTION The power does not turn on. The fuse has blown. After checking for short circuits fuse with one with the same No sound can be heard, or the Attenuator is turned on. Turn off Attenuator. volume is low. The fader or balance settings are set all Reset the fader or balance settings. side. The input/output wires or wiring harness are Reconnect the input/output wires or the wiring incorrectly. correctly. See the section on "Connecting Wires Terminals". The cassette tape is bad. Try playing another cassette tape. If works fine, the first tape was bad. The tape does not go in. / The car ignition was turned off during tape eject; or the Press the Eject button. No sound can be heard even tape was pulled out during loading, switching the mode to though the tape display is tape mode even though no tape is in. made. Nothing happens when the The computer chip in the unit is not functioning normally. Press the reset button on the unit (see p. 4). buttons are pressed. The sound quality is poor or The tape head is dirty. Clean the tape head, referring to the section on "Cleaning distorted. the tape head" (see p. 4). One of the speaker wires is being pinched by a screw in Check the speaker wiring. the car. The...