Stimmen - 7, Durchschnittliche Bewertung: 4.1
(
)
)
|
Fotos und technische Daten Hyundai H-1416 |
Anleitung Zusammenfassung
AM of FM will be displayed. • Press NEXT/TUNE-UP button or BACK/TUNE-DOWN button and then release the button when the fast scanning starts. The frequency will continue to change and will automatically stop when a broadcast station is received. • To receive a weak broadcast signal press the NEXT/TUNE-UP or BACK/TUNE-DOWN button by one press at a time and adjust the frequency you wish to receive. Saving Stations to Memory • 50 broadcast stations: 30 FM band and 20 AM stations can be stored to the preset memory. • During tuner mode, find a desired station. • Press CD FOLDER/ MEM.SET/ SKIP +10 button to activate memory setting mode. The "MEM" symbol will appear on the display. • Press NEXT/TUNE-UP button or BACK/TUNE-DOWN button to choose the desired memory location. The location number is flashing on the left side of the screen. • Press CD FOLDER/ MEM.SET/ SKIP +10 button again to store the desired station. • Repeat steps for storing stations to other locations. • To clear the memory of any location simply save a new station to the same memory. Selecting stored stations • Press CD MEMORY/REPEAT/PROG BUTTON once. "MEM" symbol will appear on the display. • Press NEXT/TUNE-UP or BACK/TUNE-DOWN button to choose the memory location. The stored station will be selected. Antenna • For FM reception, adjust the telescopic antenna appropriately to obtain the best reception on the band selected. • The AM signals are picked up through the built-in ferrite antenna. The set should be placed to a position for the best reception. FM and FM stereo reception • In particular when stereo signal is weak and much noise are received, it is preferable to receive the programmer in mono. Press STOP/ CD/USB/SD/ FM mode button to switch between FM stereo and mono modes. • If the program is received in FM stereo, "ST" indicator will light up. 5 Cassette tape playback • Slide the FUNCTION switch to TAPE position. • Press the STOP/EJECT button to open the cassette compartment. • Insert a cassette with the tape-side up into the proper Guide-rails on the inside of the cassette door. • Gently push the cassette door forward (inwards) to close it. • Press the PLAY button to start the playing. • Adjust the level of sound with VOLUME knob. Cassette controls • Press the PAUSE button to pause the playing. • Press the STOP/EJECT button to stop the playing, press the button again to open the cassette door and you can take out the tape. • When the tape plays to the end, playing will be stopped automatically and releases the PLAY button at the same time. • Press the "STOP" button followed by the "REWIND" or "FAST-FORWARD" button to rewind or forward the tape at high speed. Cassette tape recording_ • Open the cassette door by pressing the "STOP/EJECT" cassette button. • Insert a blank cassette with the tape-side up, into the proper Guide-rails on the inside of the cassette door. • Gently push the cassette door forward (inwards) to close it. • Make sure the tape is fully and properly inserted before doing so. • The set is now ready to start recording, which can be done from either the radio or CD-player. Recording from radio • Set the FUNCTION switch to RADIO position. • Tune to the desired station. • Press the PLAY button and RECORD button on deck simultaneously to start recording. • Press STOP/ EJECT button to end recording Recording from CD • Set FUNCTION switch to CD (MP3) position. • Press RECORD and PLAY buttons on cassette deck simultaneously to start recording. • Press the PAUSE button on deck. • Start the CD-player and select the exact song to be recorded. • Release the PAUSE button on deck to start recording. • Press STOP/ EJECT button to end recording. 6 Erase protection • To prevent accidental erasing of a cassette, simply break off the two plastic tabs located on the cassette tape’s rear side. • When a cassette with removed plastic tabs is inserted, the recording button cannot be pressed. • If a cassette is to be erased and re-recorded at a later stage, simply cover the holes on the cassette where the tabs were removed, with a piece of strong adhesive tape. Insertion & removal of discs_ • When opening the CD-door, always ensure the disc is not in motion (not spinning) when you open the CD-door. Always press "STOP" button to stop the disc spinning first. • Place a CD into the compartment with the label-side (printed side of disc) facing upwards. Press down in the center part of disc until the disc "locks" onto the center spindle. • When the CD has been placed onto the center spindle, gently lower the CD-door downwards until it locks shut. • The CD is now ready to be played. • To remove a disc, follow the same procedure as described above, except to remove the CD instead of inserting it into the compartment, by placing one finger at the middle of disc (center spindle) & the other at the edge of the disc & gently pulling upwards. Important : Always hold a CD by its edges. Avoid gettin...