Stimmen - 4, Durchschnittliche Bewertung: 3.8 ( )

Hersteller: Yamaha Dateigröße: 223.01 kb Dateiname: Unterrichtssprache:

YS MPX on . Recording an FM broadcast with DOLBY S NR YS and MPX FILTER indicators light. OFF . Recording with no noise reduction No indicator lights. * Dolby noise reduction manufactured under license from Dolby Laboratories Licensing Corporation. “DOLBY” and the double-D symbol Yare trademarks of Dolby Laboratories Licensing Corporation. .MPX filter: FM stations transmit a 19 kHz pilot signal in addition to the broadcast program. Sometimes this pilot signal may leak into the audio output depending on the tuner and broadcast conditions. This signal can cause improper operation of the Dolby NR systems. Activating the MPX filter (B TYPE/C TYPE/S TYPE MPX ON settings) will effectively remove the signal. AUTO TAPE TUNING button (in step 4) Pressing this button during the REC/PAUSE mode will activate the Auto Tape Tuning that makes it possible to internally determine the optimum recording characteristics (bias and recording sensitivity) according to the loaded cassette tape in about 20 seconds. To perform the Auto Tape Tuning, send the tape leader part forward and set the PLAY/TRIM control and the BIAS ADJUST control to the center position before pressing the AUTO TAPE TUNING button. When the Auto Tape Tuning is completed, the TAPE TUNING indicator lights. After completion of Auto Tape Tuning, the tape automatically rewinds to the point where the Auto Tape Tuning began and the REC/PAUSE mode is engaged. The bias adjustment with the BIAS ADJUST control is possible even after this tuning. To clear Auto Tape Tuning setting, press the AUTO TAPE TUNING button once again, or load any cassette tape of different type. * When recording on the other side of the tape, another Auto Tape Tuning is unnecessary. When recording on the same type cassette tape of a different brand, another Auto Tape Tuning is advisable for much more accurate setting of the recording characteristics. AUTO TAPE TUNING The Auto Tape Tuning function improves the quality of your recording, permitting critical adjustment of the deck’s recording bias and sensitivity for best results with every tape you use. With the Auto Tape Tuning function, the recording characteristics (recording bias and sensitivity) are automatically adjusted while recording and playback operations in about 20 seconds, to accurately match the characteristics of loaded tape. For example, the recorded (output) level (A in the figure) may differ from recording (input) level (B in the figure), due to widely varying characteristics of cassette tapes between brands. Using the Auto Tape Tuning function, these differences are effectively eliminated by adjusting the recording bias (for high frequencies) and sensitivity (for overall frequencies) according to the loaded cassette tape, making a significant contribution to overall recording quality (C in the figure). B Input Level Output Level (dB)CA Frequency (Hz) Setting the recording level (in step 3) Play the loudest passage of the source to be recorded and watch the meter readings. Adjust the REC LEVEL control so that the highest peak may not exceed the optimum levels of each tape type. Normally, it is best to adjust the BALANCE control such that the LEFT and RIGHT meter readings are even. METAL NORM HIGH dB – 302017141210 8 6 4 Y02 468 + R .The Ymark indicates the Dolby noise reduction system standard level. Bias adjustment The BIAS ADJUST control is for fine adjustment of the recording bias. Normally, it is not necessary to adjust this control since the recording bias can be automatically adjusted by the built-in Auto Tape Selector and the AUTO TAPE TUNING button for different tape types. However, if you feel that your recording needs further bias adjustment (to compensate for absent or distorted high frequencies), adjust this control to your liking. When high frequencies are When high frequencies are distorted, increase the absent, decrease the recording recording bias by turning bias by turning the BIAS the BIAS ADJUST control ADJUST control clockwise. counterclockwise. BIAS ADJUST BIAS ADJUST Synchronized recording function When operating this unit in combinaton with the YAMAHA CD Player which has SYNCHRO button on its remote control transmitter, CD Synchronized recording function can be utilized. This function is operated with the remote control transmitter of the CD Player. (Regarding the operation, refer to the manual of the CD Player.) SYNCHRO indicator of this unit lights when the SYNCHRO button of the remote controller is pressed. 0 +– + 0 – Output Level (dB)10 0 -10 -20 -30 -40 123 Frequency (Hz) 1 Insufficient bias (High frequencies are distorted.) 2 Optimum bias 3 Excessive bias (High frequencies are absent.) KX-580/KX-480 KX-380 (KX-580 only) Tape counter !! Tape counter KX-580/KX-480 KX-380 (KX-580 only) Tape counter !! Tape counter RESET button MUTE/SEARCH RESET button MUTE/SEARCH REC MUTE operation - Inserting a blank space during recording During recording A 4-second blank interval is automatically recorded on the tape,...

Herunterladen

Geben Sie zwei Ziffern: