Stimmen - 4, Durchschnittliche Bewertung: 4.5 ( )

Hersteller: Kenwood Dateigröße: 419.86 kb Dateiname: B64-1316-00.pdf Unterrichtssprache:

• Do not let unconnected cables or terminals touch metal car or anything else conducting electricity. To prevent short also do not remove the caps on the ends of the unconnected cables or the terminals. • Connect the speaker cables correctly to the terminals to which they correspond. The unit may receive damage or fail to work if you share the - cables and/or ground them to any metal part in the car. • After the unit is installed, check whether the brake lamps, indicators, wipers, etc. on the car are working properly. • Insulate unconnected cables with vinyl tape or other similar material. — 19 — Connecting English Antenna Conversion Antenna Cord (FM/AM antenna — 20 — TEL MUTE 12 34 56 78 12 34 56 78 P.CONT.OUT Rear right output (Red) Rear left output (White) Battery cable (Yellow) Ignition cable (Red) Wiring harness (Accessory1) If no connections are made, do not let the cable come out from the tab. TEL mute cable (Brown) Power control/ Motor antenna control cable (Blue/White) A–7 Pin (Red) A–4 Pin (Yellow) Connector A Connector B Fuse Connector Function Pin Numbers for ISO Connectors Cable Colour Functions External Power Connector A–4 Yellow Battery A–5 Blue/White Power Control A–7 Red Ignition (ACC) A–8 Black Earth (Ground) Connection Speaker Connector B–1 Purple Rear Right ( + ) B–2 Purple/Black Rear Right ( – ) B–3 Gray Front Right ( + ) B–4 Gray/Black Front Right ( – ) B–5 White Front Left ( + ) B–6 White/Black Front Left ( – ) B–7 Green Rear Left ( + ) B–8 Green/Black Rear Left ( – ) Connect to the terminal that is grounded when either the telephone rings or during conversation. Connect either to the power control terminal when using the optional power amplifier, or to the antenna control terminal in the vehicle. Installation Installation n Bend the tabs of the mounting sleeve with a screwdriver or simi-lar utensil and attach it in place. Metal mounting strap (commercially available) Self-tapping screw (commercial-ly available) Firewall or metal support Connecting The pin arrangement of vehicle you drive. prevent damage to The default connection 1 below. If the ISO connector 2 or 3, make the connection as illustrated. 2 WARNING Unit Vehicle Ignition cable (Red) Battery cable (Yellow) A–7 Pin (Red) A–4 Pin (Yellow) 1 (Default setting) The A-7 pin (red) tor is linked with the ignition, and the nected to the constant power supply. 2 The A-7 pin (red) of the vehicle's ISO connector is connected the constant power supply, and the A-4 pin (yellow) is linked the ignition. Screw(M4 . 8) (commercially available) Installation n Bend the tabs of the mounting sleeve with a screwdriver or simi-lar utensil and attach it in place. Metal mounting strap (commercially available) Self-tapping screw (commercial-ly available) Firewall or metal support Connecting The pin arrangement of vehicle you drive. prevent damage to The default connection 1 below. If the ISO connector 2 or 3, make the connection as illustrated. 2 WARNING Unit Vehicle Ignition cable (Red) Battery cable (Yellow) A–7 Pin (Red) A–4 Pin (Yellow) 1 (Default setting) The A-7 pin (red) tor is linked with the ignition, and the nected to the constant power supply. 2 The A-7 pin (red) of the vehicle's ISO connector is connected the constant power supply, and the A-4 pin (yellow) is linked the ignition. Screw(M4 . 8) (commercially available) Unit Vehicle NOTE Ignition cable (Red) A–7 Pin (Red) Make sure that the unit is installed securely in place. If the unit is unstable, it may malfunction (eg, the sound may skip). Battery cable (Yellow) A–4 Pin (Yellow) 3 The A-4 pin (yellow) of the vehicle's ISO connector is not connected to anything, while the A-7 pin (red) is connected to the constant power supply (or both the A-7 (red) and A-4 (yellow) pins are connected to the constant power supply). Unit Vehicle Ignition cable (Red) A–7 Pin (Red) Battery cable (Yellow) A–4 Pin (Yellow) NOTE When the connection is made as in 3 above, the unit's power will not be linked to the ignition key. For that reason, always make sure to turn off the unit's power when the ignition is turned off. To link the unit's power to the ignition, connect the ignition cable (ACC...red) to a power source that can be turned on and off with the ignition key. — 21 — Installation English ¦ Removing the hard rubber frame 1 Engage the catch locks on the lower Lower the frame and Catch Lock Accessory2 Removal tool 2 When the lower level is removed, remove the upper ¦ Removing the Unit 1 Refer to the section then remove the hard 2 Remove the screw (M4 . 8) on the back panel. 3 Insert the two removal tools as shown. Screw (M4X8) (commercially available) 4 inside. Lower the removal tool out the unit halfway whilst pressing towards the 5 The frame can be removed from the top side in the same manner. ful not to drop it. toward the bottom, and pull Pull the unit all the way out with your hands, being care-Be careful to avoid injury from the catch pins on the removal tool. Catch facing up NOTE 2 CAUTION — 2...

Herunterladen

Geben Sie zwei Ziffern: