Stimmen - 3, Durchschnittliche Bewertung: 3.7
(
)
)
|
Anleitung Zusammenfassung
In accordance with FCC requirements, changes or modifications not expressly approved by Thomson Consumer Electronics could void the user’s authority to operate this product. HAVE A BLAST - JUST NOT IN YOUR EARDRUMS! Make sure you turn down the volume on the unit before you put on the headphones. Increase the volume to the desired level only after headphones are in place. ©1997 Thomson Consumer Electronics, Inc. Trademark(s) ® Registered Marca(s) ® Registradas Model RP-1540 97-46 20703270 (Rev. 1, E/S) Printed in China all weather design This unit is splash-resistant and not designed to be used underwater. DO NOT SUBMERGE. • Avoid exposing the unit to saltwater or salt spray. • To ensure watertight seal of battery compartment, check to make sure the cabinet area around the compartment is free of dirt and water before opening. Be sure to close battery compartment cover firmly after installing batteries. The in-ear headphones are not water-resistant and are not intended for use under water. DO NOT SUBMERGE. Caution/Care Do not expose the unit to extreme temperatures, such as those caused by a hot stove or the inside of a car parked in the summer sun. Such conditions can damage the unit. Always clean with a soft cloth, dampened with water only. Tape use 1. Open cassette door, lift top cover and insert tape, exposed side up. Close door and put down top cover. 2. Plug headphones into jack and set VOLUME to minimum level. 3. Slide RADIO/TAPE switch to TAPE. 4. Press PLAY to start tape play. When tape ends, the unit will automatically reverse direction and play the other side. To manually reverse tape and play other side, press ( ) button. 5. Set BASS BOOST and VOLUME at desired level. 6. Press STOP to end tape play. Always stop tape play before opening cassette door. 7. Use FAST FORWARD button to quickly advance tape and REWIND button to quickly move tape backward. Always stop tape play before and after fast forwarding Service This product should be serviced only by those specially trained in appropriate servicing techniques. For instructions on how to obtain service, refer to the warranty in this guide. Attach your sales receipt for future reference, or write down the date you purchased/received this product as a gift. This information will be valuable if service should be required during the warranty period. Purchase Date________________ Name of Store ________________ AUTO REVERSE BASS BOOST -TUNING + HOUR 4 5 +5 BAND 1 2 3 MEM MODE ALARM ALARMOFF MIN TUNING (+,-) and Preset 1-5 and +5 buttons MEM button BAND button ALARM OFF button ALARM button MODE button FM MONO/STEREO switch (inside) RESET button (inside) HOUR/ MIN buttons FFWD REW PLAY STOP Tape function buttons Auto reverse button Tape direction button Battery Compartment BASS BOOST ON • • OFF PHONES RADIO • • TAPE VOLUME VOLUME PHONES jack BASS BOOST switch RADIO/TAPE switch Battery Installation 1. Open battery compartment by squeezing tab in and pulling up cover. 2. Install the two "AA" renewable alkaline batteries included. 3. Replace battery door. Important Battery Information • Alkaline or alkaline renewable batteries are recommended. • Rechargeable batteries may result in shorter playing time. • Remove batteries if storing the unit for a month or more to avoid leakage. • Dispose of batteries in the proper manner, according to federal, state and local regulations. • Any battery may leak electrolyte if mixed with a different battery type; if inserted incorrectly; if all batteries are not replaced at the same time; if disposed of in fire; or if an attempt is made to charge a battery not intended to be recharged. • Discard leaky batteries immediately to avoid possible skin burns or other personal injury. ANTENNAS The headphone cord serves as the FM antenna. Because this antenna is directional, repositioning can improve reception. The built-in AM antenna is somewhat directional. It may be necessary to slightly rotate the unit to strengthen weak AM signals. Radio Use 1. Plug headphones into jack. Set volume to minimum level. NOTE: Always set volume to minimum level, turn radio on and put headphones in place before adjusting to desired volume. 2. Slide RADIO/TAPE switch to RADIO. 3. Use BAND button to choose AM or FM. Display will show active band. 4. Put BASS BOOST on and adjust VOLUME to desired level. 5. Slide RADIO/TAPE switch to TAPE to turn radio off. TUNING 1. Use up (+) and down (-) buttons to tune in radio stations. Display will show active frequency. 2. To scan through frequencies, press up (+) or down (-) button momentarily. When a clear signal is captured, scanning will automatically stop. To manually stop scanning, press up (+) or down (-) button again. PRESET TUNING This unit can store up to 10 preset stations - AM or FM in memory. 1. Choose band and frequency. 2. Press MEM. MEMORY will blink in display. 3. Choose a PRESET button from 1 to 5. The station is now stored. After 5 seconds, MEMORY disappears from display. 4. To store more than 5 st...